Zoom In

Adding bolt-on horsepower to the 997 Turbo is a continuous quest by many enthusiasts looking for more power. Reverting back to old tuning technologies, Agency Power has developed a larger throttle body and plenum kit for the Porsche 997 Turbo to gain added performance. The point of a larger throttle body is to get in more air.

The more air you bring in, the more power you make. The 997 Turbo's engine intake system works off pulses, so how that air is diverted to either side of the engine is not as important as the volume incoming. The plenum kit includes an OEM Porsche Cayenne Turbo throttle body (part# 94860511503) which is a direct bolt on and plug in for the electronic throttle control with no modifications needed.

This throttle body has a 77.64mm inner diameter compared to the stock one of 75.64mm. We chose to go with this smaller diameter throttle body to give the car more low end horsepower and torque. If the diameter of the throttle body is to big, it will increase turbo lag and performance gains will only be made at the mid to top end RPM range. Since most 997 Turbo users drive their car on the street and track, we developed this product to substantially increase throttle response and improve "usable" power.

The Agency Power plenum kit is made using high quality 6061 aluminum that has been TIG welded and pressure tested in a T shape to mimic the OEM design. The CNC machined 4 bolt throttle body flange features a groove to accompany a rubber o-ring to ensure a secure and sealed fit with the OEM Porsche Cayenne throttle body. The T plenum features the necessary fittings for stock vacuum hoses and breather lines and includes a 1 way check valve needed. Each T plenum is powder coated gloss black for an OEM look and includes new silicone couplers in black and worm clamps to secure it to the factory intake manifolds. The installation of the plenum requires removal of the factory airbox and Y pipe to access the component.

Installation of the Agency Power plenum kit DOES NOT require the ECU to be flashed. The factory ECU will adjust accordingly to the change in throttle body diameter. However, corresponding mods including an ECU flash will only bring out additional power. As it stands alone, the plenum kit will add a bolt on 20 wheel horsepower to your Porsche 997 Turbo. As tested on a VR700 kit, the plenum added nearly 45 horsepower and 60 ft/lbs of torque. Splitting and diverting the air flow and directing it towards the cylinders at a much higher air speed.

Recommended installation time is approximately 3 hours.

HP Gains: 40-45Bhp. 60 ft/lbs of torque

Fits:
Porsche 997 Turbo

Zoom In

The revolutionary 997 Turbo IPD “Y” Pipe was built for the more demanding Turbo performance customer. This is not a cast reproduction of the factory Y pipe but a complete re-design from scratch, developed to deliver even greater air flow for both stock AND highly modified Turbos.

The factory Y pipe becomes restrictive when adding substantial power gains. The IPD “Y” Pipe has larger inlets and an optimized diversion area allowing for even greater power gains. This superior and more efficient design flows 126 more cfm than the factory Y pipe delivering the additional power needed to raise the performance bar on any Turbo.

Bigger isn’t always better, and the IPD “Y” Pipe is designed to deliver optimum flow without being too large causing a loss in boost response. These “Y” Pipes can also be special ordered in custom powder coated colors and ceramic coatings or polished to improve the aesthetic appeal of your Turbo engine.

The IPD 997 Turbo Y Pipe is designed to be a direct replacement of the factory OEM Y Pipe. There are no modifications or fabrication required for installing the IPD Y Pipe. This is an easy and straight forward R & R (remove and reinstall) bolt on upgrade.

997.2 Turbo Hi-Flow Y Pipe: HP Gains 15-20. Direct Bolt-in Replacement / No modification necessary

Fits:
Porsche 997 Turbo MKII

The incredible 997 Porsche Turbo is the most revolutionary and capable Porsche Turbo to ever come out of Germany. The already explosive power can be further increased with the new 997 Turbo IPD Intake Plenums.

The patented IPD Plenum design works exceptionally well with all forced induction applications and the 997 Turbo is no exception. Power and torque increases provided by the IPD plenum are impressive and stay over and above all factory power curves from launch to redline. Maximum power increases take place in the midrange where it's most needed and most critical.

Maximum horsepower gains range from 30 to 35 depending on vehicle condition and pre-existing mods. The 997 Turbo plenums deliver smooth and linear power with considerably quicker boost response creating a longer and more desirable power band. The Turbo plenums deliver reliable performance for both street and motorsport applications enhancing the already visceral Porsche Turbo driving experience.

Unlike the 996 Turbo the 997 Turbo requires an “adaptation” period that can be fully realized with either a series of hard pulls on the dyno or 10 to 50 miles of hard driving which of course IPD recommends only be performed on a closed circuit race track.

The 997 Turbo has an extremely sensitive ECU/DME making it prone to external environmental corrections so it is imperative that proper, adequate and consistent cooling be available when you dyno any of the 997 Turbos to get accurate and reliable dyno figures both before and after each test.

Installation of all Turbo Plenums is highly recommended to be performed by qualified and trained Porsche technicians.

Turbo customers looking to increase engine power without pushing the motorsport envelope to redline would best benefit from the 74mm IPD Turbo Plenum.

This version of the 997 Turbo plenum utilizes the factory 74mm throttle body and delivers impressive performance gains for both stock and slightly modified Turbos with exhaust and software.

The 74mm IPD Turbo Plenum is also designed to perform with the higher flowing IPD “Y” Pipe.

Fits:
Porsche 997 Turbo

BMC air filters are designed and produced to ensure a higher air flow than original paper filters. In F1, for example, BMC cotton filters minimize the loss of air flow pressure passing through the air filter; this way ensures the best conditions for full exploitation of maximum power. Therefore the benefits of replacing the original paper filter with BMC cotton air filter, produced using the same technology and materials as the F1 air filters, are evident.

DESIGN AND MATERIALS
Qualified engineers using advanced software and expert technicians using the latest technologies produce BMC air filters. An F1 filter must be very light, must be made of the best raw materials and must improve performance. For this reason we use only alloy mesh with epoxy coating to ensure protection from petrol fumes and from oxidization due to the humidity of the air. The filtering material is composed of a special cotton gauze soaked with low-viscosity oil to give you the best air permeability.


This Product Fits:


Porsche 997 Turbo GT2 X51 / S 2009>>

Panel Filter Size:
- width - 245mm
- height - 150mm

BMC air filters are designed and produced to ensure a higher air flow than original paper filters. In F1, for example, BMC cotton filters minimize the loss of air flow pressure passing through the air filter; this way ensures the best conditions for full exploitation of maximum power. Therefore the benefits of replacing the original paper filter with BMC cotton air filter, produced using the same technology and materials as the F1 air filters, are evident.

DESIGN AND MATERIALS
Qualified engineers using advanced software and expert technicians using the latest technologies produce BMC air filters. An F1 filter must be very light, must be made of the best raw materials and must improve performance. For this reason we use only alloy mesh with epoxy coating to ensure protection from petrol fumes and from oxidization due to the humidity of the air. The filtering material is composed of a special cotton gauze soaked with low-viscosity oil to give you the best air permeability.


This Product Fits:


Porsche 997 Turbo 3.8L / S PDK 2008>>

Panel Filter Size:
- width - 187mm
- height - 631mm

Zoom In

Recharger Filter Care Service Kit (aerosol)

A six-step maintenance system designed to clean any K&N Filtercharger® Air Filter.

Restores air flow efficiency so your Filtercharger performs like new!

Includes:
6.5 oz. Spray Oil & 12 oz. Filter Cleaner

Please note this item can not be sent out by plane. Deliveries only to European countries by road service