Direct-to-Head Throttle Bodies
Patented technology that helps to increase air flow dramatically thus minimising air flow separation and reduces turbulence, resulting in higher volumetric efficiency.
This pristine technology with Knife-edged butterflies has improved inlet airflow and performance significantly. With the individual Throttle blades very close to the inlet valves, the engine and Throttle response are vastly improved. Along with this, we have also found an impressive increase in Horsepower, Torque, Driveability, and an incredible mechanical soundtrack.
Installation Packages are suitable for Porsche 911 SC - 3.0L engines (Model Years 1974-1985).
Throttle Bodies come fully assembled and ready to bolt directly to the Cylinder Heads, with the following parts included:
• Aerospace Grade Billet Aluminium "Shaft-less" Individual Throttle Bodies.
• Aluminium Inlets/Extensions are suitable for duck or whale tail models.
• Aluminium Ram Pipes.
• Throttle Position Sensors (TPS) Mounting Kits.
• Billet Aluminium Fuel Rails.
• Thermal Insulation Gaskets.
• Throttle Linkage System which connects directly to the existing OEM cable pick-ups.
• Available in 18 anodised colour options.
• Available with 39mm Inlet Ports.
Installation Kit:
• ECU including base map package - Comes complete with full electrical engine harness, Coil pack, HT leads, engine sensors, hardware and software.
• Trigger Wheel & Fan Pulley assembly, including sensor mounting bracket and Distributor blanking plug.
• Fuelling System - Includes Fuel Injectors, Fuel pressure regulator with gauge, Fuel Lines, fittings and hoses to interface with existing fuel system
• Vacuum System - Includes vacuum take-off & idle air control assembly, c/w interfacing pipework for cold start engine idle control & brake boost assit.
• Engine Oil breather system - Includes all filters and interfacing components required.
• Megaflow Air Filtration System - Includes Megaflow Air Filters complete with brushed aluminium pre-drilled Filter back plates.
• Heater duct system.
**please note
Race Mesh Ram Pipe Installation Kit is not included
this is extra product code 102-101-00087-01
Parts are in silver. The contents of these kits may vary, from the images provided
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
102-102-00238-01KIT
The product you are viewing cross references to these numbers
- Porsche 911 1974-1977 2.7L / 1976-77 3.0 Carrera
- Porsche 911 1978-1983 3.0L / SC
Patented technology that helps to increase air flow dramatically thus minimising air flow separation and reduces turbulence, resulting in higher volumetric efficiency.
This pristine technology with Knife-edged butterflies has improved inlet airflow and performance significantly. With the individual Throttle blades very close to the inlet valves, the engine and Throttle response are vastly improved. Along with this, we have also found an impressive increase in Horsepower, Torque, Driveability, and an incredible mechanical soundtrack.
Installation Packages are suitable for Porsche 911 - 3.2L engines (Model Years 1986-1989).
Throttle Bodies come fully assembled and ready to bolt directly to the Cylinder Heads, with the following parts included:
• Anodised Aerospace Grade 6082/T6 Billet Aluminium "Shaft-less" Individual Throttle Bodies.
• Anodised Aluminium Inlets/Extensions suitable for flatdeck & ducktail models.
• Aluminium Ram Pipes & Assembly Tool.
• Throttle Position Sensor (TPS).
• Billet Aluminium Fuel Rails, Including PICO 377cc Fuel Injectors.
• Thermal Insulation Gaskets.
• Throttle Linkage System which connects directly to the existing OEM cable pick-ups.
• Air Filtration System - Includes Megaflow Air Filters complete with brushed aluminium pre-drilled Filter back plates.
Supporting parts that create these Full Plug, Play and Tune - Installation Kits:
• ECU GP Lite patch harness including base map package - Comes complete with electrical patch harnesses, hardware, and software.
• Fuelling System - Includes Fuel pressure regulator with gauge, Fuel Lines, fittings, and hoses to interface with existing fuel system
• Vacuum System - Includes vacuum take-off & idle air control assembly, c/w interfacing pipework for cold start engine idle control & brake boost assist.
• Engine Oil breather system - Includes all filters and interfacing components required.
• Heater duct system.
**please note
Race Mesh Ram Pipe Installation Kit is not included
this is extra product code 102-101-00086-01
Parts are in silver. The contents of these kits may vary, from the images provided
- Porsche 911 1984-1986 3.2L
- Porsche 911 1987-1989 3.2L G50
Patented technology that helps to increase air flow dramatically thus minimising air flow separation and reduces turbulence, resulting in higher volumetric efficiency.
This pristine technology with Knife-edged butterflies has improved inlet airflow and performance significantly. With the individual Throttle blades very close to the inlet valves, the engine and Throttle response are vastly improved. Along with this, we have also found an impressive increase in Horsepower, Torque, Driveability, and an incredible mechanical soundtrack.
Installation Packages are suitable for Porsche 911 - 3.2L engines (Model Years 1986-1989).
Kits are made in Silver
Throttle Bodies come fully assembled and ready to bolt directly to the Cylinder Heads, with the following parts included:
• Anodised Aerospace Grade 6082/T6 Billet Aluminium "Shaft-less" Individual Throttle Bodies.
• Anodised Aluminium Inlets/Extensions suitable for flatdeck & ducktail models.
• Aluminium Ram Pipes & Assembly Tool.
• Throttle Position Sensor (TPS).
• Billet Aluminium Fuel Rails, Including PICO 377cc Fuel Injectors.
• Thermal Insulation Gaskets.
• Throttle Linkage System which connects directly to the existing OEM cable pick-ups.
• Air Filtration System - Includes Megaflow Air Filters complete with brushed aluminium pre-drilled Filter back plates.
Supporting parts that create these Full Plug, Play and Tune - Installation Kits:
• ECU GPA full harness including base map package - Comes complete with electrical full harnesses, hardware, and software.
• Fueling System - Includes Fuel pressure regulator with gauge, Fuel Lines, fittings, and hoses to interface with existing fuel system
• Vacuum System - Includes vacuum take-off & idle air control assembly, c/w interfacing pipework for cold start engine idle control & brake boost assist.
• Engine Oil breather system - Includes all filters and interfacing components required.
• Heater duct system.
**please note
Race Mesh Ram Pipe Installation Kit is not included
this is extra product code 102-101-00086-01
Parts are in silver. The contents of these kits may vary, from the images provided
- Porsche 911 1984-1986 3.2L
- Porsche 911 1987-1989 3.2L G50
Patented technology that helps to increase air flow dramatically thus minimising air flow separation and reduces turbulence, resulting in higher volumetric efficiency.
This pristine technology with Knife-edged butterflies has improved inlet airflow and performance significantly. With the individual Throttle blades very close to the inlet valves, the engine and Throttle response are vastly improved. Along with this, we have also found an impressive increase in Horsepower, Torque, Driveability, and an incredible mechanical soundtrack.
Installation Packages are suitable for Porsche 911 - 3.2L engines (Model Years 1986-1989).
Throttle Bodies come fully assembled and ready to bolt directly to the Cylinder Heads, with the following parts included:
• Anodised Aerospace Grade 6082/T6 Billet Aluminium "Shaft-less" Individual Throttle Bodies.
• Anodised Aluminium Inlets/Extensions suitable for flatdeck & ducktail models.
• Aluminium Ram Pipes & Assembly Tool.
• Throttle Position Sensor (TPS).
• Billet Aluminium Fuel Rails, Including PICO 377cc Fuel Injectors.
• Thermal Insulation Gaskets.
• Throttle Linkage System which connects directly to the existing OEM cable pick-ups.
• Air Filtration System - Includes Megaflow Air Filters complete with brushed aluminium pre-drilled Filter back plates.
Supporting parts that create these Full Plug, Play and Tune - Installation Kits:
• ECU including base map package - Comes complete with electrical patch harnesses, hardware, and software.
• Fuelling System - Includes Fuel pressure regulator with gauge, Fuel Lines, fittings, and hoses to interface with existing fuel system
• Vacuum System - Includes vacuum take-off & idle air control assembly, c/w interfacing pipework for cold start engine idle control & brake boost assist.
• Engine Oil breather system - Includes all filters and interfacing components required.
• Heater duct system.
**please note
Race Mesh Ram Pipe Installation Kit is not included
this is extra product code 102-101-00086-01
Parts are in silver. The contents of these kits may vary, from the images provided
- Porsche 911 1984-1986 3.2L
- Porsche 911 1987-1989 3.2L G50
Patented technology that helps to increase air flow dramatically thus minimising air flow separation and reduces turbulence, resulting in higher volumetric efficiency.
This pristine technology with Knife-edged butterflies has improved inlet airflow and performance significantly. With the individual Throttle blades very close to the inlet valves, the engine and Throttle response are vastly improved. Along with this, we have also found an impressive increase in Horsepower, Torque, Driveability, and an incredible mechanical soundtrack.
Porsche 911E, T and S 1969 to 1973 (2.2 and 2.4 Ltr) engines.
Throttle Bodies come fully assembled and ready to bolt directly to the Cylinder Heads, with the following parts included:
• Aerospace Grade Billet Aluminium "Shaft-less" Individual Throttle Bodies.
• Aluminium Inlets/Extensions are suitable for duck or whale tail models.
• Aluminium Ram Pipes.
• Throttle Position Sensors (TPS) Mounting Kits.
• Billet Aluminium Fuel Rails.
• Thermal Insulation Gaskets.
• Throttle Linkage System which connects directly to the existing OEM cable pick-ups.
• Available in 18 anodised colour options.
• Available with 39mm Inlet Ports.
Installation Kit:
• Emerald3D-K6 ECU including base map package, complete with full electrical engine harness/ Trigger Wheel & Fan Pulley Assembly, hardware, and software.
• Fuelling System - Includes Fuel pressure regulator with gauge, Fuel Lines, fittings, and hoses to interface with existing fuel system
• Vacuum System - Includes vacuum take-off kit for brake boost an/or Idle Air Control (IAC) assembly, c/w interfacing pipework for cold start engine idle control & brake boost assist.
• Engine Oil breather system - Includes all filters and interfacing components required.
• Heater duct system - for interior (Cabin) heating.
• Rain Guard Kit for protection against rain water ingress.
**please note
Race Mesh Ram Pipe Installation Kit is not included
this is extra product code 102-101-00088-01
Parts are in silver. The contents of these kits may vary, from the images provided
- Porsche 911 1965-1968 2.0L / 912 SWB (F)
- Porsche 911 1968-1973 2.2L / 2.4L / 2.7L RS LWB (F)
Patented technology that helps to increase air flow dramatically thus minimising air flow separation and reduces turbulence, resulting in higher volumetric efficiency.
This pristine technology with Knife-edged butterflies has improved inlet airflow and performance significantly. With the individual Throttle blades very close to the inlet valves, the engine and Throttle response are vastly improved. Along with this, we have also found an impressive increase in Horsepower, Torque, Driveability, and an incredible mechanical soundtrack.
Installation Packages are suitable for Porsche 911 SC - 3.0L engines (Model Years 1974-1985).
Throttle Bodies come fully assembled and ready to bolt directly to the Cylinder Heads, with the following parts included:
• Aerospace Grade Billet Aluminium "Shaft-less" Individual Throttle Bodies.
• Aluminium Inlets/Extensions are suitable for duck or whale tail models.
• Aluminium Ram Pipes.
• Throttle Position Sensors (TPS) Mounting Kits.
• Billet Aluminium Fuel Rails.
• Thermal Insulation Gaskets.
• Throttle Linkage System which connects directly to the existing OEM cable pick-ups.
• Available in 18 anodised colour options.
• Available with 39mm Inlet Ports.
Installation Kit:
• GPA ECU including base map package - Comes complete with full electrical engine harness, Coil pack, HT leads, engine sensors, hardware and software.
• Trigger Wheel & Fan Pulley assembly, including sensor mounting bracket and Distributor blanking plug.
• Fuelling System - Includes Fuel Injectors, Fuel pressure regulator with gauge, Fuel Lines, fittings and hoses to interface with existing fuel system
• Vacuum System - Includes vacuum take-off & idle air control assembly, c/w interfacing pipework for cold start engine idle control & brake boost assit.
• Engine Oil breather system - Includes all filters and interfacing components required.
• Megaflow Air Filtration System - Includes Megaflow Air Filters complete with brushed aluminium pre-drilled Filter back plates.
• Heater duct system.
**please note
Race Mesh Ram Pipe Installation Kit is not included
this is extra product code 102-101-00087-01
Parts are in silver. The contents of these kits may vary, from the images provided
- Porsche 911 1974-1977 2.7L / 1976-77 3.0 Carrera
- Porsche 911 1978-1983 3.0L / SC
Patented technology that helps to increase air flow dramatically thus minimising air flow separation and reduces turbulence, resulting in higher volumetric efficiency.
This pristine technology with Knife-edged butterflies has improved inlet airflow and performance significantly. With the individual Throttle blades very close to the inlet valves, the engine and Throttle response are vastly improved. Along with this, we have also found an impressive increase in Horsepower, Torque, Driveability, and an incredible mechanical soundtrack.
Porsche 911E, T and S 1969 to 1973 (2.2 and 2.4 Ltr) engines.
Throttle Bodies come fully assembled and ready to bolt directly to the Cylinder Heads, with the following parts included:
• Aerospace Grade Billet Aluminium "Shaft-less" Individual Throttle Bodies.
• Aluminium Inlets/Extensions are suitable for duck or whale tail models.
• Aluminium Ram Pipes.
• Throttle Position Sensors (TPS) Mounting Kits.
• Billet Aluminium Fuel Rails.
• Thermal Insulation Gaskets.
• Throttle Linkage System which connects directly to the existing OEM cable pick-ups.
• Available in 18 anodised colour options.
• Available with 39mm Inlet Ports.
Installation Kit:
• GPA ECU including base map package, complete with full electrical engine harness/ Trigger Wheel & Fan Pulley Assembly, hardware, and software.
• Fueling System - Includes Fuel pressure regulator with gauge, Fuel Lines, fittings, and hoses to interface with existing fuel system
• Vacuum System - Includes vacuum take-off kit for brake boost an/or Idle Air Control (IAC) assembly, c/w interfacing pipework for cold start engine idle control & brake boost assist.
• Engine Oil breather system - Includes all filters and interfacing components required.
• Heater duct system - for interior (Cabin) heating.
• Rain Guard Kit for protection against rain water ingress.
**please note
Race Mesh Ram Pipe Installation Kit is not included
this is extra product code 102-101-00088-01
Parts are in silver. The contents of these kits may vary, from the images provided
- Porsche 911 1965-1968 2.0L / 912 SWB (F)
- Porsche 911 1968-1973 2.2L / 2.4L / 2.7L RS LWB (F)
Patented technology that helps to increase air flow dramatically thus minimising air flow separation and reduces turbulence, resulting in higher volumetric efficiency.
This pristine technology with Knife-edged butterflies has improved inlet airflow and performance significantly. With the individual Throttle blades very close to the inlet valves, the engine and Throttle response are vastly improved. Along with this, we have also found an impressive increase in Horsepower, Torque, Driveability, and an incredible mechanical soundtrack.
Throttle Bodies come fully assembled and ready to bolt directly to the Cylinder Heads, with the following parts included:
• Anodised Aerospace Grade 6082/T6 Billet Aluminium "Shaft-less" Individual Throttle Bodies.
• Anodised Aluminium Inlets/Extensions suitable for flatdeck & ducktail models.
• Aluminium Ram Pipes & Assembly Tool.
• Throttle Position Sensor (TPS).
• Billet Aluminium Fuel Rails, Including PICO 377cc Fuel Injectors.
• Thermal Insulation Gaskets.
• Throttle Linkage System which connects directly to the existing OEM cable pick-ups.
you will need an EFI Installation & control kit which is not included
**please note
Race Mesh Ram Pipe Installation Kit is not included
this is extra product code 102-101-00086-01 The contents of these kits may vary, from the images provided
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
102-102-00239-01
The product you are viewing cross references to these numbers
- Porsche 911 1984-1986 3.2L
- Porsche 911 1987-1989 3.2L G50
Patented technology that helps to increase air flow dramatically thus minimising air flow separation and reduces turbulence, resulting in higher volumetric efficiency.
This pristine technology with Knife-edged butterflies has improved inlet airflow and performance significantly. With the individual Throttle blades very close to the inlet valves, the engine and Throttle response are vastly improved. Along with this, we have also found an impressive increase in Horsepower, Torque, Driveability, and an incredible mechanical soundtrack.
Throttle Bodies come fully assembled and ready to bolt directly to the Cylinder Heads, with the following parts included:
• Anodised Aerospace Grade 6082/T6 Billet Aluminium "Shaft-less" Individual Throttle Bodies.
• Anodised Aluminium Inlets/Extensions suitable for flatdeck & ducktail models.
• Aluminium Ram Pipes & Assembly Tool.
• Throttle Position Sensor (TPS).
• Billet Aluminium Fuel Rails, Including PICO 377cc Fuel Injectors.
• Thermal Insulation Gaskets.
• Throttle Linkage System which connects directly to the existing OEM cable pick-ups.
Parts are in silver.
**please note
Race Mesh Ram Pipe Installation Kit is not included
this is extra product code 102-101-00087-01
you will need an EFI Installation & control kit which is not included
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
102-102-00238-01
The product you are viewing cross references to these numbers
- Porsche 911 1974-1977 2.7L / 1976-77 3.0 Carrera
- Porsche 911 1978-1983 3.0L / SC
Our unique patented technology helps to increase air flow dramatically thus minimising air flow separation and reduces turbulence, resulting in higher volumetric efficiency.
This pristine technology with Knife-edged butterflies has improved inlet airflow and performance significantly. With the individual Throttle blades very close to the inlet valves, the engine and Throttle response are vastly improved. Along with this, we have also found an impressive increase in Horsepower, Torque, Driveability, and an incredible mechanical soundtrack.
Throttle Bodies come fully assembled and ready to bolt directly to the Cylinder Heads, with the following parts included:
• Aerospace Grade Billet Aluminium "Shaft-less" Individual Throttle Bodies.
• Aluminium Inlets/Extensions are suitable for duck or whale tail models.
• Aluminium Ram Pipes.
• Throttle Position Sensor (TPS) choices calibrated to the options available from the AT Power range. .
• Billet Aluminium Fuel Rails.
• Thermal Insulation Gaskets.
• Throttle Linkage System which connects directly to the existing OEM cable pick-ups.
The owner of his 911E was totally lost for words on the difference these throttles and performance kits have made to how his car now drives. It starts without fail, it feels much faster, better acceleration between the gears, it looks incredible under the engine lid and sounds amazing.
This product fits
Porsche 911E, T and S 1969 to 1973 (2.2 and 2.4 Ltr) engines.
The throttles will be supplied in silver
The contents of these kits may vary, from the images provided you will need an EFI Installation & control kit which is not included
**please note
Race Mesh Ram Pipe Installation Kit is not included
this is extra product code 102-101-00088-01
you will need an EFI Installation & control kit which is not included
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
102-102-00237-01
The product you are viewing cross references to these numbers
- Porsche 911 1968-1973 2.2L / 2.4L / 2.7L RS LWB (F)
- Engine Rebuild Kit
- Gaskets & Sets
- Radial Seal / RMS / Camshaft / Balance shaft
- Intermediate shaft (IMS)
- Oil System Parts
- Fuel System Parts
- Belts / Tensioners / Rollers
- Chains & Tensioners
- Timing covers and gaskets
- Engine Bearings / Shells
- Engine Valves / Guides / Springs
- Rocker Arms & Tappets
- Engine Bolts / Studs
- Piston Rings
- Engine Cylinders / Liners / Pistons
- Connecting Rod
- Cylinder Head / Camshaft Carrier
- Camshaft covers / Gaskets
- Camshafts
- Camshaft gears / sprockets and fixings
- Crankcase Parts
- Crankshaft & Parts
- Engine Tinware
- Engine Mounts
- Turbo Chargers / Intercoolers & Parts
- Air Intake & Injection
- Carburetors & Parts
- PMO Carburetors
- Vacuum Pump
- Jenvey Throttle Bodies
- Specialist Tools