Wiring Harness / Cables
Fits:
Porsche 924S - 1986 to 1988
For LHD (Left Hand Drive) cars and RHD (Right Hand Drive)
Complete engine harness
Connectors:
- Female 35 pin connector to DME Motronic ECU
- 4 x Injector
- 9 Pin Connector for 12V+
- Air Flow Sensor
- Altitude Compensation Switch
- Code Plug
- DME Connection Plug
- Idle Positioner
- Oil Level Switch
- Oil Pressure Send
- Oil Pressure Warn
- Oxygen Sensor
- Reference Mark Sensor
- Speed Transmitter
- Temperature Sensor
- Throttle Valve Switch
- Water Temperature Sensor
- Water Temperature Send
Materials:
TXL Wires (Temperature Rating to +125 C)
Polyethylene Terephthalate (PET) Loom (Temperature Rating to +125 C)
RW Harness Total Weight - 1.05lbs
OEM Harness Total Weight - 1.85lb
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
94460703002
The product you are viewing cross references to these numbers
- Porsche 924S 2.5L 1986-87
- Porsche 924S 2.5L 1988
Fits:
Porsche 924S - 1986 to 1988
Porsche 944 - 1982 to 1991
Porsche 944 turbo - 1985 to 1991
Porsche 968 - 1992 to 1995
Porsche 911 - 1984 to 1989
Connector will fit Bosch units
0 281 200 076
0 281 200 050
Connector List:
- 35 Pin ECU Connector
- Wire Seals
- JPT Terminals
- Connector Screws
Features:
After three decades of heat and extreme environmental conditions, the connectors and wires become extremely brittle and fragile and can break. Oftentimes, they break by just unplugging them. This can cause signal loss and prevent your engine from starting.
This OEM+ replacement kit will replace the stock ECU Bosch DME connector.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
94461200207
The product you are viewing cross references to these numbers
- Porsche 911 1984-1986 3.2L
- Porsche 911 1987-1989 3.2L G50
- Porsche 911 1978-1989 3.3L Turbo (930)
- Porsche 924S 2.5L 1986-87
- Porsche 924S 2.5L 1988
- Porsche 944 2.5L 8V 1982-87
- Porsche 944 2.7L 8V 1988-89
- Porsche 944S 2.5L 16V 1987-88
- Porsche 944S2 3.0L 16V 1989-91
- Porsche 944 Turbo 2.5L 8V 1985-88
- Porsche 944 Turbo 2.5L 8V 1989-91
- Porsche 944 Turbo S 2.5L 8V 1988>>
- Porsche 968 3.0L 1992-94
- Porsche 968 Sport 3.0L 1994-95
- Porsche 968 CS 3.0L 1993-95
- Porsche 968 Turbo S 3.0L 1993-94
Fits:
Porsche 924S - 1986 to 1988
Porsche 944 - 1982 to 1989
Porsche 944 turbo - 1986 to 1991
This Porsche 944 Injector Harness will replace your brittle and old connectors, terminals, wires and loom.
The fuel injector section of the factory harness connector has been exposed to three decades of high heat cycles and extreme environmental conditions. As a result, the wires and connectors become brittle and broken, which can cause problems with engine performance.
This OEM+ replacement harness with yellow labels will ensure a cleaner engine bay, using brand-new connectors and wires, and sealed boots.
The harness will be routed through the elephant's boot, down the main branch, and into the DME at the passenger's footwell. A full pinout and instruction manual will be provided with the harness.
- TXL Wires (Temperature Rating to +125 C)
- Polyethylene Terephthalate (PET) Loom (Temperature Rating to +125 C)
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
94460611201
The product you are viewing cross references to these numbers
- Porsche 924S 2.5L 1986-87
- Porsche 924S 2.5L 1988
- Porsche 944 2.5L 8V 1982-87
- Porsche 944 2.7L 8V 1988-89
- Porsche 944S 2.5L 16V 1987-88
- Porsche 944S2 3.0L 16V 1989-91
- Porsche 944 Turbo 2.5L 8V 1985-88
- Porsche 944 Turbo 2.5L 8V 1989-91
- Porsche 944 Turbo S 2.5L 8V 1988>>
- Air Mass/Flow Sensors
- Alternator / Generator
- Batteries & Chargers
- Distributor Cap
- Rotor Arms / Point Sets
- Relays / Fuses
- Ignition Coil
- Ignition Lead Sets
- Ignition Lead High Performance
- Injectors
- Starter Motors
- Idle Control Valve
- Fuel Pump
- Fan / Temperature Switch
- Alternator / Fan belts
- Speed / Reference / Knock Sensors