A 型摇臂

Powerflex Heritage Collection Replacement A-frame Arm Top & Bottom Bush.
Fits OE Wishbone Front (A-Frame) part numbers 91134190100 /91134190200.

SET OF 4 BUSHES



Fits:
Does not fit models made before 1969, fits all models 1969 to 1989.
Porsche 911 1969-89
Porsche 912
Porsche 914 1970-76

Fits to No. 14 on the diagram


Powerflex Heritage Collection. For Modern Day Classics.

A range of bushes engineered for the road to compliment your classic car.

POWERFLEX Heritage Collection bushes are manufactured using modern day materials with properties biased for the road. These dark grey coloured bushes will improve any collector's car, whilst retaining the same standard appearance of a rubber bush.

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

PFF57-401H

您正在查看的产品与这些编号存在交叉引用关系

Powerflex Black Series Replacement A-frame Arm Top & Bottom Bush.
Fits OE Wishbone Front (A-Frame) part numbers 91134190100 / 91134190200.

SET OF 4 BUSHES



Fits:
Does not fit models made before 1969, fits all models 1969 to 1989.
Porsche 911 1969-89
Porsche 912
Porsche 914 1970-76

Fits to No. 14 on the diagram

Powerflex Black Series - Designed for the Track - Ready to Race - Engineered to be the best.

Powerflex Black Series bushes are manufactured using a 95 Shore A compound to provide maximum control of chassis geometry. This compound can be up to 80% more resistant to load than standard rubber and 25% stiffer than our purple performance material.

If your requirements are purely for the ultimate in handling and chassis performance then Powerflex Black Series are unique, offering the most precise and accurate alignment for your chassis.

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

PFF57-401BLK

您正在查看的产品与这些编号存在交叉引用关系

Powerflex Replacement A-frame Arm Top & Bottom Bush.
Fits OE Wishbone Front (A-Frame) part numbers 91134190100 /91134190200.

SET OF 4 BUSHES



Fits:
Does not fit models made before 1969, fits all models 1969 to 1989.
Porsche 911 1969-89
Porsche 912
Porsche 914 1970-76

Fits to No. 14 on the diagram

Powerflex. Replacing your car rubber suspension bushes with Polyurethane Suspension Bushes will give you:

- Better road holding
- Constant steering geometry
- Increased tyre life
- More responsitive steering
- Longer service life of suspension components

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

PFF57-401

您正在查看的产品与这些编号存在交叉引用关系

SuperPro Replacement A-frame Arm Top & Bottom Bush.
SET OF 4 bushes.



Fits:
Porsche 911 1970-89

Replacing your car rubber suspension bushes with Polyurethane Suspension Bushes will give you:

- Better road holding
- Constant steering geometry
- Increased tyre life
- More responsive steering
- Longer service life of suspension components

Click 'Zoom in' for large parts diagram
Fits to No. 14 on the diagram

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

SPF0236AK

您正在查看的产品与这些编号存在交叉引用关系

A-Frame Spherical control arm bearings (Set of 4) Front, For Porsche 911 / 930 Turbo

Fits:
Porsche 911 1969-89
Porsche 930 Turbo

Sphericals™ performance bearings deliver a new level of handling and ride quality. This is the only performance bushing replacement that delivers ball-type spherical bearing action with stock front control arms.

The secret is in the ball-shaped bearing that allows continuous self-alignment, preventing binding and allowing the suspension to work and move freely. Springs and dampers do their job of controlling the suspension without interference from excessive friction or binding from the bushings.
spherical-bearing-cad-animation-001

Self-aligning spherical ball action – cutaway view
Sphericals Eliminate Binding

With ordinary performance bushings, binding happens when the axis of the front and rear mounts are not collinear. Their hard-compound and minimal compliance cause even minor misalignment of the mounts to pinch and bind, preventing free movement of the control arm. Binding can happen in both static (car is stationary) and dynamic (chassis is flexing) conditions. Sphericals eliminate binding
Dynamic Binding

Dynamic binding is due to chassis flex. This happens anytime the car is cornering, braking, accelerating, or going over bumps. Control arm mounts move with the chassis flex, deviating from their static alignment to cause binding, pinching and resisting free movement of the suspension. The chassis flexes when you most need free suspension movement; to absorb bumps, and during hard cornering when you need grip for performance.

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

2051001

您正在查看的产品与这些编号存在交叉引用关系

Front control A arm rubber bushing kit. 1 kit required per car.
DIY Bushings Kit.



Fits:
Porsche 911/912/930/914 1968-89 with installation tools

Front control arm rubber bushings are now available as a kit for self-installation. In addition to a complete set of 4 OEM spec rubber bushings, the kit includes our proprietary installation tools and instructions which are essential for successful installation. Use a pipe clamp or shop press to complete the install.

Restore Ride and Performance
Rubber is the choice if you want to restore factory ride and performance in a zero-maintenance solution.

Quality Design
Don't confuse Elephant Racing OEM spec control arm bushings with inferior products offered without installation tools. Those products have a loose fit to allow tool-less installation. The loose fit causes excessive bushing deformation, torsion bar rubbing, premature wear, bushing slippage, and changing corner balance. Be sure you are getting genuine Elephant Racing OEM spec bushings.

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

2290000

您正在查看的产品与这些编号存在交叉引用关系

聚青铜控制臂轴承，前部。
价格为每套套件的价格。每辆车需要一套套件。

#大象赛跑#

适合：
保时捷 911 / 912 / 930 1968-89 年
保时捷 914


PolyBronze 轴承优于塑料衬套替代品，原因如下：
悬架支架是粗糙的金属板冲压件。它们往往不圆，并且存在不规则性，这会使普通聚氨酯衬套变形，挤压和粘住摩擦表面。聚氨酯具有“抓地力”，摩擦系数本身就很高，与挤压聚氨酯衬套相结合会产生很大的摩擦力。结果是驾驶体验不佳，轮胎附着力降低。

PolyBronze 具有坚固的青铜轴承芯，不会变形。聚氨酯外套可吸收安装不规则性，同时青铜内轴承保持稳定，提供自由移动的机械配合，可实现精密滚道。提供的润滑脂配件使重新润滑变得轻而易举，8 字形凹槽可将润滑脂固定在位。

这种组合可实现零吱吱声和无摩擦的悬架运动。非常适合街道或赛道，乘坐舒适。

PolyBronze 是一种精密青铜轴承，外壳为聚氨酯外壳。这种组合既能提供平稳的滑动体验，又能提供金属轴承的极致性能。

✔ 无吱吱声或卡住
✔ 极其平稳的乘坐体验
✔ 比橡胶衬套更容易安装
✔ 集成式注油嘴和注油槽

正面


相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

2051500

您正在查看的产品与这些编号存在交叉引用关系

HD front control / A-arm bushing kit.
SET OF 4 One set per car.  85 Shore rating 



Fit:
Porsche 911 / 930 1969-89
Porsche 914 1970-76


High Density bushings for Porsche 911 and 914 front A-Arms are a direct replacement for your old rubber bushings. Eliminate steering slop brought on by 40+ year old rubber and improve suspension geometry under all conditions with our 25% stiffer HD bushings. Due to the large surface area inherent in the design of the 911 and 914 torsion bar based control arms these are particularly important to achieving your car's potential both on and off the track. Sold as a complete set and machined out of a tougher rubber compound, these are the perfect compliment for any street or track setup.

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

91134190100

您正在查看的产品与这些编号存在交叉引用关系

Lower Control Arm Reinforcement Kit. 

1 kit required per car



Fits:
Porsche 911 - 1969 to 1989
Porsche 911 turbo - 1975 to 1989
Porsche 912 - 1976
Porsche 914 - 1970 to 1976

Avoid Control Arm Failure

For Safari type cars we recommend reinforcing the control arms to help cope with the additional forces that off-road vehicles must deal with. 

These precision cut steel plates and gussets are to be welded at strategic locations to strengthen the factory control arms.

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

2051002

您正在查看的产品与这些编号存在交叉引用关系

Low-friction control arm mounts.
1 pair req'd per car.



Fits:
Porsche 911 / 912 / 930 1968-89

Non-Binding, Friction- Free Movement
Elephant Racing's proprietary-design Low-Friction Control Arm Mounts allow for free control arm movement, eliminating any potential for binding. We've corrected a key factory design limitation; our mounts self-align in all axis, becoming collinear to avoid binding as the arm moves through its range of motion.

Factory Mounts and Binding
911 series and 914 factory control arm mounts pivot allow for self-alignment in the horizontal plane only. Any misalignment in the vertical plane results in pinching and binding at the bushing that resists free movement of the control arm.
Non-colinear axis binding

Factory mounting points (stamped sheet metal) are imprecise at best and can be substantially off due to frontal impacts, pot holes, or suspension pan replacement. If the mounts are not collinear, the control arm will bind with any performance bushing compound or bearing.

Self-Aligning Low-Friction Mounts
Our Low-Friction Control Arm Mounts self-align in both the horizontal and vertical planes. The result is collinear front and rear mounts delivering smooth non-binding action. You get superior performance and a smoother ride.

Control Arm Mount Kit
Kit includes everything required to upgrade one car. Factory rear mounts are replaced with our self-aligning mounts. Factory front mounts are retained and augmented with self-aligning washers.

With this kit installed, both front and rear control arm mounts self-align in both vertical and horizontal planes. They become collinear, allowing free non-binding motion of the control arm.

Our mounts replicate the factory form factor and work in conjunction with Polybronze bearings, polyurethane, or any other hard compound bushing or bearing. Fits both aluminum and steel suspension cross-members.

For Fitting Instructions please CLICK HERE

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

2071600

您正在查看的产品与这些编号存在交叉引用关系

Wishbone front A-frames fitted with HD Bushes (Set of 2 Left & Right )  

Two A-frame wishbones fitted with Heavy Duty bushing. 85 Shore rating 

Fits:
Porsche 911 1974-89
Porsche 930 Turbo

Click "Zoom in" to see the diagram.
Diagram Ref No 14.

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

3602409111

您正在查看的产品与这些编号存在交叉引用关系