Brake Fluid
- Porsche Cayenne V6 3.6L Petrol 300Hp
- Porsche Cayenne V6 3.0L Diesel 245HP
- Porsche Cayenne S V6 3.0L Hybrid 380HP
- Porsche Cayenne S V8 4.8L Petrol 400HP
- Porsche Cayenne S V8 4.2L Diesel 382HP
- Porsche Cayenne GTS V8 4.8L Petrol 400HP
- Porsche Cayenne Turbo V8 4.8L Petrol 500HP
- Porsche Cayenne Turbo S V8 4.8L Petrol 550HP
710 Racing brake fluid has been specifically formulated to provide the highest performance at the extreme temperatures experienced under race conditions. Suitable for racing or other higher performance vehicles, both on and off road, it also meets the performance requirements of the International FMVSS 116 DOT4 specification.
Dry Boiling Point ------ Exceeds 300deg C
Wet Boiling Point ------ Exceeds 195deg C
For the highest performance change brake fluid before every race or competitive event, especially if brake temperatures are known to be high.
710 Racing Brake Fluid is not suitable for use in certain Citroen and other vehicles requiring a mineral based fluid (LHM). It should not be used in vehicles fitted with magnesium alloy cylinders or reservoirs. Silicone type assembly compounds should not be used in conjunction with this product.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
710
The product you are viewing cross references to these numbers

This Brake Bleeder Kit by MityVac will make this dreaded chore easy, clean, and quick.
Illustrated booklet makes your troubleshooting easy.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
00072180241
The product you are viewing cross references to these numbers


Boiling point brake fluid testing is the only test method approved by brake & brake fluid manufacturers
- Increase service revenue & road safety
- Accurate, reliable & repeatable results
- Operates off the vehicles own 12 volt battery
- Measures up to 320°, suitable for use on all grades of brake fluid including racing fluids
- Multilanguage: English, German, French, Spanish, Italian
Find out about Textar product verification here

Brake fluid is one of the most important fluids in a car as without it, stopping the vehicle safely would be impossible. The Brake fluid transmits the force exerted by the driver on the brake pedal onto the wheel brake.
To ensure perfect operation of the brakes, the brake fluid must be changed regularly during inspection or maintenance and tested with the correct brake fluid tester.
Brake fluid should be changed every two years.
The higher the DOT class, the higher the boiling temperature and wet boiling point. Higher DOT classes tend to allow longer maintenance intervals. The DOT standards are based on the American FMVSS-116 standard of the Department of Transportation (DOT).
Boiling Point and Viscosity
Dry Boiling Point - describes the property of the sealed new brake fluid. In this state, the brake fluid is almost anhydrous (substance containing no water). The dry boiling point is usually between 240 and 280°C.
Wet Boiling Point - determines the property of the brake fluid at the end of its life cycle, at a water content of 3.5% the fluid should be replaced. This defined wet boiling point must not be undercut.
Viscosity - describes the flow rate of the brake fluid. The lower the viscosity, the faster the brake fluid flows through the brake system, and the faster the brake signals are transmitted.
Important Notes
• Brake fluid is poisonous and a hazardous waste.
• Be careful when changing. The fluid weakens paints and plastics.
• It must not come into contact with eyes or skin. Always rinse spilled liquid with water.
• Do not pour the liquid into drinking water or mix with used oil.
• The colour of the brake fluid reveals nothing about its quality.
• Brake fluid should be stored in its original packaging and in a dry, cool and well-ventilated place.
Find out about Textar product verification here


DOT 4
Having an extremely high boiling point and lower viscosity than required, it meets and greatly exceeds regulatory standards. Also suitable for vehicles with ABS.
Vapour Lock formation
This sort of habit leaves room for the Vapour Lock, the formation of vapour bubbles due to boiling of the brake fluid that replace the normal fluid and are compressed, thereby sending the brake pedal to its fill stoke (spongy pedal). The origin is incident in the porosity of the tubes that make up the braking circuit, which in time draw moisture into the fluid, drastically reducing the boiling point. The result is a reduced braking efficiency.
Brembo Premium Brake Fluid
Brembo Premium brake fluids have a higher boiling point that exceeds the standard, thus offering superior resistance to the Vapour Lock and ensuring braking efficiency even at low temperatures. With high anti-corrosion properties and resistance to oxidation, Brembo brake fluid also allows for long-term unaltered chemical/physical characteristics of the fluid in operating circuit; therefore, preserving its integrity.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
L040
The product you are viewing cross references to these numbers

Brake fluid DOT 4 LV (Low Viscosity) Textar.
Textar DOT 4 LV (Low Viscosity) is especially recommended for use in hydraulic brake and clutch systems of vehicles fitted with ESP, ABS and ASR with a high boiling point and outstanding performance at very low temperatures.
DOT 4 LV (Low Viscosity)
Dry Boiling Point ≥ 260° C
Wet Boiling Point ≥ 165° C
Viscosity at -40C < 750 mm2 /s
Brake fluid is one of the most important fluids in a car as without it, stopping the vehicle safely would be impossible. The Brake fluid transmits the force exerted by the driver on the brake pedal onto the wheel brake.
To ensure perfect operation of the brakes, the brake fluid must be changed regularly during inspection or maintenance and tested with the correct brake fluid tester.
Brake fluid should be changed every two years.
The higher the DOT class, the higher the boiling temperature and wet boiling point. Higher DOT classes tend to allow longer maintenance intervals. The DOT standards are based on the American FMVSS-116 standard of the Department of Transportation (DOT).
Boiling Point and Viscosity
Dry Boiling Point - describes the property of the sealed new brake fluid. In this state, the brake fluid is almost anhydrous (substance containing no water). The dry boiling point is usually between 240 and 280°C.
Wet Boiling Point - determines the property of the brake fluid at the end of its life cycle, at a water content of 3.5% the fluid should be replaced. This defined wet boiling point must not be undercut. <
Viscosity - describes the flow rate of the brake fluid. The lower the viscosity, the faster the brake fluid flows through the brake system, and the faster the brake signals are transmitted.
Important Notes
• Brake fluid is poisonous and a hazardous waste.
• Be careful when changing. The fluid weakens paints and plastics.
• It must not come into contact with eyes or skin. Always rinse spilled liquid with water.
• Do not pour the liquid into drinking water or mix with used oil.
• The colour of the brake fluid reveals nothing about its quality.
• Brake fluid should be stored in its original packaging and in a dry, cool and well-ventilated place.
Find out about Textar product verification here
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
95006
The product you are viewing cross references to these numbers


Brake fluid is one of the most important fluids in a car as without it, stopping the vehicle safely would be impossible. The Brake fluid transmits the force exerted by the driver on the brake pedal onto the wheel brake.
To ensure perfect operation of the brakes, the brake fluid must be changed regularly during inspection or maintenance and tested with the correct brake fluid tester.
Brake fluid should be changed every two years.
The higher the DOT class, the higher the boiling temperature and wet boiling point. Higher DOT classes tend to allow longer maintenance intervals. The DOT standards are based on the American FMVSS-116 standard of the Department of Transportation (DOT).
Boiling Point and Viscosity
Dry Boiling Point - describes the property of the sealed new brake fluid. In this state, the brake fluid is almost anhydrous (substance containing no water). The dry boiling point is usually between 240 and 280°C.
Wet Boiling Point - determines the property of the brake fluid at the end of its life cycle, at a water content of 3.5% the fluid should be replaced. This defined wet boiling point must not be undercut.
Viscosity - describes the flow rate of the brake fluid. The lower the viscosity, the faster the brake fluid flows through the brake system, and the faster the brake signals are transmitted.
Important Notes
• Brake fluid is poisonous and a hazardous waste.
• Be careful when changing. The fluid weakens paints and plastics.
• It must not come into contact with eyes or skin. Always rinse spilled liquid with water.
• Do not pour the liquid into drinking water or mix with used oil.
• The colour of the brake fluid reveals nothing about its quality.
• Brake fluid should be stored in its original packaging and in a dry, cool and well-ventilated place.
Find out about Textar product verification here
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
95002
The product you are viewing cross references to these numbers


PAGID Racing Street+ for Road Use:
Meet the perfect addition for street performance.
Street+ Brake Fluid is the ideal companion to Street+ Brake Pads, ensuring great stopping power and reliability every drive.
- Specification DOT: DOT 5.1
- Wet Boiling Point: 180 °C
- Dry Boiling Point: 260 °C
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
SBF-0500B
The product you are viewing cross references to these numbers


Reliability and high quality
Brembo Racing | SPORT | EVO 500++ brake fluid is ideal in all conditions, fit for all, from everyday driving to non-professional intermediate use on the track.
This is a reliable high quality fluid that improves pedal feel and consistent braking performance without the frequent inspection intervals of a full racing brake fluid.
Formulated for real enthusiasts
- Suitable for use in braking systems designed for non-mineral fluids.
- Purposely designed to meet the expectations of enthusiasts who demand a lot from their system.
- Exceeds the requirements of specification U.S. FMVSS No.116 DOT 3 and DOT 4, SAE J1703, SAE J1704 and ISO 4925 (classes 3 and 4).
- Compatible with other DOT 3, DOT 4 and DOT 5.1 brake fluids, as long as they comply with the above specification.
For safety reasons, it is recommended to replace your brake fluid at least once a year. Not Suitable for vehicles with mineral oil systems. Colour range: appearance from transparent to amber. In the case of new brake fluid, when poured out from the sealed bottle, the colour may differ from the range, but the performance remains the same.


This high temperature brake fluid designed for the most extreme racing conditions.
It has a dry boiling point of 335° C which is around 25° C higher than a typical racing brake fluid. Developed exclusively for competition use, Brembo HTC 64T provides the highest performance under all racing conditions and has been used in F1, ALMS, DTM, WRC and BTCC.
Very high dry boiling point (335°C) / Wet boiling point 203°C
Ideal for competition vehicles which experience high brake temperatures
Successfully used in top level Motorsport including F1
For maximum performance it is recommended that Brembo HTC 64T is not mixed with other brake fluids.
500ml Bottle
Please Note
Must not be used in brake systems containing magnesium parts

Brembo Racing LCF 600 plus has been specifically formulated to provide the highest performance under all racing conditions:

-an independently proven low compressibility at high temperatures
-a typical dry boiling point of 316°C (601°F)
-a typical wet boiling point of 204°C (399°F)
It even exceeds the requirements of U.S. FMVSS 116 DOT4 specification.

For brake systems and is highly temperature-resistant (up to 1,000°C).
Available in 75ml tube and 5ml sachet
The advantages of Cera Tec:
• Non-conductive and contains no solids
• Suitable for ABS
• Facilitates brake installation
• Reduces brake squealing
• Protects against scoring and corrosion
• Free of copper and acids
• Pressure-resistant / high viscosity
Cera Tec is also suitable for lubricating:• Disc- and drum-brake systems
• Compressors
• Centralised lubrication systems
• Axle bearings
• Chains
• Seat rails
• Sunroof tracks
• Battery terminals
Application:
Apply a thin layer of Cera Tec on the marked sections
Find out about Textar product verification here
Formula DOT 5.1, Re-branded as Factory R Dot 5.1- Yellow Bottle with Yellow cap.
Factory R Dot 5.1 is AP Racing's high performance non silicone based brake and clutch fluid. Recommended for use in the hydraulic brake and clutch systems of all cars, for which a non petroleum based fluid is specified.
Suitable for high performance applications including vehicles fitted with ABS and ESP, is suitable for road and track day use.
Designation.
- Factory R DOT 5.1
'Typical' Boiling Points.
- New Dry 269°C
- 'Wet' E.R. 180°C
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
CP4510
The product you are viewing cross references to these numbers

Hydra tec lubricant for maintenance work and protection Textar
Available in 180ml Tube, 75ml Tube or 5ml Sachet
The Advantages of Hydra Tec:
- Facilitates the installation of hydraulic brake components
- Tested compatibility with commercially available braking fluids (DOT3, DOT4, DOT4LV, DOT5.1)
- Free of mineral oils and compatible with EPDM rubber
- In addition, running surfaces are protected against corrosion
Hydra Tec is suitable for lubricating:
- Cylinder running surfaces
- Pistons
- Sealing elements
Application:
Apply a thin layer of Hydra Tec on the marked sections.
Note:
Hydra Tec should be applied thinly and evenly.
Never use mineral oils or greases as substitutes.
Do not apply the product on friction surfaces of brake pads or brake discs.
Find out about Textar product verification here


Motul DOT 3 & 4 Synthetic Brake Fluid is a fully synthetic, advanced brake and clutch fluid designed to deliver exceptional thermal resistance and stability, ensuring reliable braking performance even under extreme conditions.
- High Performance: Provides consistent and effective braking under the most demanding conditions.
- Advanced Formula: Technically advanced, 100% synthetic brake fluid formulated on a polyglycol basis, suitable for all types of hydraulic brake and clutch systems that comply with DOT 4 and DOT 3 specifications.
- Thermal Resistance: Offers exceptionally high thermal resistance and stability, with a dry boiling point of 245°C / 473°F and a wet boiling point of 158°C / 316°F.
Compatibility:
Recommended Applications:
- Suitable for all hydraulic brake and clutch systems that meet DOT 4 and DOT 3 manufacturers’ specifications.
Specifications:
- Complies with FMVSS 116 DOT 4 and DOT 3; SAE J 1703 standards.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
102718
The product you are viewing cross references to these numbers

