Electronic Control Units

12v to 6v converter for dash gauges and radio. 



Fits:
Porsche 356
Porsche 356A
Porsche 356B
Porsche 356C

Are you converting your 6v 356 to 12v but want to keep the gauges and radio as original?

This inverter can be used if you have converted you car from 6 volts to 12 volts. Use this converter for your 6 volts gauges and radio with a max output of 10 Amps. 

This converter comes in a solid case with mounting holes.

For use in combination with the wiper motor you need 64462830112/1. This is the 30 Amp inverter. And can be used for the gauges, radio and wiper all together.

Red = input 12 V
Black = ground - (2x)
Yellow= 6 volt output.

12v to 6v converter for wiper motor, dash gauges and radio.



Fits:
Porsche 356
Porsche 356A
Porsche 356B
Porsche 356C

Are you converting your 6v 356 to 12v but want to keep the wiper motor, dash gauges and radio as original?

This inverter can be used if you have converted you car from 6 volts to 12 volts. Use this converter for your 6 volts wiper motor, dash gauges and radio with a max output of 30 Amps. 

This converter comes in a solid aluminium case with mounting holes.

There is also a 10 amp version if you don't need a wiper motor conversion - 64462830103/1

Red = input 12 V
Black = ground 
Yellow= 6 volt output.

CDI ignition module Bluetooth Programming Dongle, fits with Perma Tune 3 pin and 6 Pin Cdi boxes.



Fits:
Porsche 911 1974-77
Porsche 911 1978-83
Porsche 930 3.3L 1978-89

The new generation ignition boxes make diagnostics easier. The controller monitors and runs diagnoses programs automatically and is read by two coloured LED function lights the are viewable from underneath the unit. The diagnoses can also be done via this Bluetooth programming dongle.

New Perma Tune unit.

For Bluetooth Installation Instruction CLICK HERE

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

90506

The product you are viewing cross references to these numbers

Ignition Starter box CDI (HKZ) Bluetooth Programming Cable, fits with Perma Tune 3 pin and 6 Pin Cdi boxes.



Fits:
Porsche 356 12V
Porsche 911 1974-77
Porsche 911 1978-83
Porsche 930 3.3L 1978-89

The 90502 USB Smart Wire allows you to customize your Perma-Tune Ignition module program. It plugs into the USB port of a computer and then installs itself automatically. It also powers up the module for programming with a single plug without having to connect anything else to the module. The programming software is downloaded from the internet, free, so the module settings can then be changed, saved and organized as text files.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

90502

The product you are viewing cross references to these numbers

Ignition module. Porsche 356 or early 911 12 Volt or 8 Volt ignition cars.



Disclaimer: Before fitting this CDI unit please make sure the new PERMA-TUNE coil is being fitted with it. Do not try to start the car with Blue Bosch coil made in Brazil. This will damage the Perma-Tune CDI box and void the warranty. If CDI unit was not purchased with the PERMA-TUNE coil the warranty will not be respected. Fitting with other brand coils at your own risk.

Bluetooth programmable (Bluetooth Smart Wire required part no 90506)

Brand: Perma Tune
This is an upgrade for the ignition system. Basically it puts the load of the ignition system through the box rather than the distributor. You take the existing wiring and run it through this box and the points then become an earth trigger switch for the box rather than switching the coil.


This Model is the first of a brand new product line for Perma-Tune. We have combined our accumulated knowledge of Porsche ignition over the last 48 years and applied it to the very latest electronics technology to produce a state of the art electronic ignition module that is period correct looking. Made to look like an old school electrical relay, it blends right into the engine bay of a 356 or an early 911.

NO CRIMPS, NO MESS, NO HEADACHES
Plug and play features eliminate the need for wire crimps and complicated wiring diagrams. Wires are cut and stripped, then inserted into the wire bus for a secure, plug in connection without the need for special tools or wire crimps.

Simple, four wire installation. There is no need to interpret complicated wiring diagrams, the terminals are clearly marked so you know exactly where each wire goes.

NO DIALS, NO SWITCHES, NO PROBLEMS
Installation is easy. There are no dials to turn, no switches to set and no chips to plug in. The 356906 Perma-Tune comes to you pre-programmed and ready to be installed on a 356. You can always customise the module later using your wireless device to make secure, reliable configuration changes through the built in Bluetooth connection.

STRONG, YET FORGIVING
The Perma-Tune ignition module features on board diagnostics to help you install the module. The built in strobe light can help you check your ignition timing. It also has self resetting overload protection so there are no fuses to replace.

SMART CONNECTIONS
Use any kind of distributor you have. The Points distributor connection will work with breaker points or any aftermarket distributor.

The tachometer output connection is universal and will work with the stock tachometer or aftermarket electronic tachometer, shift light and RPM switch.

Power connects to 12 Volt or 8 Volt systems. Six Volt converters are not available at this time.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

356906

The product you are viewing cross references to these numbers