Electronic Control Units

3 Pin CDI (HKZ) ignition module.
Premium version
(Bosch reference 227-200-001)



New Perma Tune Gen 6

Fits:
Porsche 911 1965-77
Porsche 914/6

Disclaimer: Before fitting this CDI unit please make sure the new PERMA TUNE coil is being fitted with it. Do not try to start the car with Blue Bosch coil made in Brazil. This will damage the Perma-Tune CDI box and void the warranty. If CDI unit was not purchased with the PERMA TUNE coil the warranty will not be respected. Fitting with other brand coils at your own risk.

The Gen 6 Premium Perma-Tune CDI module makes diagnostics easier by providing onboard diagnostics that are automatically displayed by two coloured LED function lights.
These LED lights assist in diagnosing both the ignition module and the car. The green LED is a status indicator that can flash diagnostic fault codes. The red LED is a strobe light that flashes each time the coils fires in the same manner as a timing light which is especially useful for detecting engine misfire.
The LED function lights are mounted in the harness electrical connector and can only be seen with a mirror while the module is powered up.
As an additional feature of the Perma-Tune Premium module, there are three self-resetting overload protectors that protect your Perma-Tune and your car from overload damage. The overload protectors are hidden underneath the ignition module so they do not spoil the original look of the part.

The Premium ignition module features a die cast housing that has been treated to mimic the patina of the original aluminum die cast distributor and has a range of digital features that the Basic module does not have. The Premium module provides full control over RPM limit, mechanical advance timing, power output, multi spark function and has many other features that can be programmed using a computer, tablet or smart phone. The 911906 comes preprogrammed for the Porsche 911 so programming changes are optional. The programmable mechanical advance feature is very handy for restoring a distributor advance curve that has been distorted by worn mechanical parts without having to replace the weights and springs. Scroll down for more complete information about your programming options.

DISTRIBUTOR TRIGGER SIGNAL

The second most common cause of SC engine ignition failure is the ignition trigger circuit.
Since the ignition box is controlled by the magnetic pulse generator located inside the distributor, any disruption in the triggering signal will cause the ignition box to malfunction. Be aware that the connectors can push back in the housing. Pull the rubber boot back to inspect the connection between the box and harness.
Full disassembly and inspection of the distributor is highly recommended due to the intermittent nature of triggering problems. Pay special attention to the distributor trigger shielded cable ( green wire ), magnetic pulse generator magnet and magnetic pulse generator winding connection as these parts are known to fail in combination. An especially common problem is a broken magnet pole. Evidence of arching between the magnetic pulse generator magnet points indicates a defective rotor. In this case replace the rotor, magnetic pulse winding, green wire and ignition box. The Perma-Tune high performance triggering is so accurate that worn out distributor shaft bearings can be detected by the tachometer. This is indicated by the tachometer needle slightly bouncing at idle. Trigger signal problems can cause double triggering which results in a weak ignition spark. Due to the lower triggering resolution of the stock ignition box, some symptoms of trigger signal problems can be more evident after the Perma-Tune is installed. Refer to the vehicle maintenance manual for triggering signal wave form specifications and distributor repair instructions.
To quickly test the triggering circuit without the use of an oscilloscope: Unplug the harness connector from the ignition box. Refer to the 911SC Installation Instructions diagram, connect an Ohm meter between pins 3 and 6 of the harness connector. To prevent the possibility of misdiagnosis, tug on the green triggering signal wire located at the base of the distributor while viewing the meter. The published specification for the magnetic pulse generator is 600 Ohms +- 100. Our experience has shown that a variation of +- 25 Ohm indicates a need to repair defective connections or to replace the magnetic pulse generator windings.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

91160270700

The product you are viewing cross references to these numbers

3 pin Ignition module CDI (HKZ) box
Basic version
(Bosch reference 227-200-001)



Disclaimer: Before fitting this CDI unit please make sure the new PERMA-TUNE coil is being fitted with it. Do not try to start the car with Blue Bosch coil made in Brazil. This will damage the Perma-Tune CDI box and void the warranty. If CDI unit was not purchased with the PERMA-TUNE coil the warranty will not be respected. Fitting with other brand coils at your own risk.

Perma-Tune Gen 6

Fits:
Porsche 911 1965-77
Porsche 914/6

Take your pick: Basic or Premium

The Gen 6 Perma-Tune comes in two models: the Model Premium ignition module and the Basic ignition module.

The Basic model is just that, basic: it performs only the same functions as the analog modules did back in the day. For the average street car, this may be all that is desired and of course is more affordable than the Premium model.
It is however still a high performance part and is perfect for racing venues that do not allow programmable digital ignition systems. The Basic model has a smooth, more original looking housing than the Gen 5 cast housing.

DISTRIBUTOR TRIGGER SIGNAL

The second most common cause of SC engine ignition failure is the ignition trigger circuit.
Since the ignition box is controlled by the magnetic pulse generator located inside the distributor, any disruption in the triggering signal will cause the ignition box to malfunction. Be aware that the connectors can push back in the housing. Pull the rubber boot back to inspect the connection between the box and harness.
Full disassembly and inspection of the distributor is highly recommended due to the intermittent nature of triggering problems. Pay special attention to the distributor trigger shielded cable ( green wire ), magnetic pulse generator magnet and magnetic pulse generator winding connection as these parts are known to fail in combination. An especially common problem is a broken magnet pole. Evidence of arching between the magnetic pulse generator magnet points indicates a defective rotor. In this case replace the rotor, magnetic pulse winding, green wire and ignition box. The Perma-Tune high performance triggering is so accurate that worn out distributor shaft bearings can be detected by the tachometer. This is indicated by the tachometer needle slightly bouncing at idle. Trigger signal problems can cause double triggering which results in a weak ignition spark. Due to the lower triggering resolution of the stock ignition box, some symptoms of trigger signal problems can be more evident after the Perma-Tune is installed. Refer to the vehicle maintenance manual for triggering signal wave form specifications and distributor repair instructions.
To quickly test the triggering circuit without the use of an oscilloscope: Unplug the harness connector from the ignition box. Refer to the 911SC Installation Instructions diagram, connect an Ohm meter between pins 3 and 6 of the harness connector. To prevent the possibility of misdiagnosis, tug on the green triggering signal wire located at the base of the distributor while viewing the meter. The published specification for the magnetic pulse generator is 600 Ohms +- 100. Our experience has shown that a variation of +- 25 Ohm indicates a need to repair defective connections or to replace the magnetic pulse generator windings.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

91160270700

The product you are viewing cross references to these numbers

6 Pin CDI (HKZ) ignition module.
Premium version
(Bosch Ref 0227300004)



New Perma Tune Gen 6

Disclaimer: Before fitting this CDI unit please make sure the new coil is being fitted with it. Do not try to start the car with Blue Bosch coil made in Brazil. This will damage the Perma-Tune CDI box and void the warranty.

Fits:
Porsche 911 1978-83
Porsche 930 3.3L 1978-89 (US cars only)

Take your pick: Basic or Premium

The Gen 6 Perma-Tune for the 911SC comes in two models: the Premium ignition module and the Basic ignition module.

The Premium ignition module features a smooth, matt finish that mimics the patina of the original aluminum die cast part.
It provides full control over RPM limit, mechanical advance timing, power output, multi spark function and has many other features that can be programmed using a computer, tablet or smart phone.
This comes preprogrammed for the Porsche 911SC so programming changes are optional. The programmable mechanical advance feature is very handy for restoring a distributor advance curve that has been distorted by worn mechanical parts without having to disassemble and repair the distributor.
The Gen 6 Premium Perma-Tune makes diagnostics easier by providing onboard diagnostics that are automatically displayed by two coloured LED function lights. These LED lights assist in diagnosing both the vehicle and the ignition module. The green LED is a status indicator that can flash diagnostic fault codes. The red LED is a strobe light that flashes each time the coils fires in the same manner as a timing light. This LED is especially useful for detecting intermittent engine misfire caused by wiring or distributor problems.
These LED function lights are mounted in the harness electrical connector and can only be seen when the module is powered up. There are three self-resetting overload protectors that assist in troubleshooting while protecting your Perma-Tune from damage. The overload protectors are hidden underneath the ignition module so they do not spoil the original look of the part. Refer to the Diagnostics section of this web site for more information about the diagnostics system and overload protectors.

For more information about this product Click Here

DISTRIBUTOR TRIGGER SIGNAL
The second most common cause of SC engine ignition failure is the ignition trigger circuit. Since the ignition box is controlled by the magnetic pulse generator located inside the distributor, any disruption in the triggering signal will cause the ignition box to malfunction. Be aware that the connectors can push back in the housing. Pull the rubber boot back to inspect the connection between the box and harness.
Full disassembly and inspection of the distributor is highly recommended due to the intermittent nature of triggering problems. Pay special attention to the distributor trigger shielded cable ( green wire ), magnetic pulse generator magnet and magnetic pulse generator winding connection as these parts are known to fail in combination. An especially common problem is a broken magnet pole. Evidence of arching between the magnetic pulse generator magnet points indicates a defective rotor. In this case replace the rotor, magnetic pulse winding, green wire and ignition box. The Perma-Tune high performance triggering is so accurate that worn out distributor shaft bearings can be detected by the tachometer. This is indicated by the tachometer needle slightly bouncing at idle. Trigger signal problems can cause double triggering which results in a weak ignition spark. Due to the lower triggering resolution of the stock ignition box, some symptoms of trigger signal problems can be more evident after the Perma-Tune is installed. Refer to the vehicle maintenance manual for triggering signal wave form specifications and distributor repair instructions.
To quickly test the triggering circuit without the use of an oscilloscope: Unplug the harness connector from the ignition box. Refer to the 911SC Installation Instructions diagram, connect an Ohm meter between pins 3 and 6 of the harness connector. To prevent the possibility of misdiagnosis, tug on the green triggering signal wire located at the base of the distributor while viewing the meter. The published specification for the magnetic pulse generator is 600 Ohms +- 100. Our experience has shown that a variation of +- 25 Ohm indicates a need to repair defective connections or to replace the magnetic pulse generator windings.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

93060270200

The product you are viewing cross references to these numbers

6 Pin CDI (HKZ) ignition module.
Basic version
(Bosch Ref 0227300004)



New Perma-Tune Gen 6 Unit

Disclaimer: Before fitting this CDI unit please make sure the new coil is being fitted with it. Do not try to start the car with Blue Bosch coil made in Brazil. This will damage the Perma-Tune CDI box and void the warranty.

Fits:
Porsche 911 1978-83
Porsche 930 3.3L 1978-89 (US cars only)

Take your pick: Basic or Premium

The Gen 6 Perma-Tune for the 911SC comes in two models: the Premium ignition module and the Basic ignition module.

The Basic model is just that, basic: it performs only the same functions as the analog modules did back in the day.
For the average road car, this may be all that is desired and of course is more affordable than the Premium model.
It is however still a high performance part and is perfect for racing venues that do not allow programmable digital ignition systems. The Basic model has a smooth, more original looking housing than the Gen 5 cast housing.

For more information about this product Click Here

DISTRIBUTOR TRIGGER SIGNAL
The second most common cause of SC engine ignition failure is the ignition trigger circuit. Since the ignition box is controlled by the magnetic pulse generator located inside the distributor, any disruption in the triggering signal will cause the ignition box to malfunction. Be aware that the connectors can push back in the housing. Pull the rubber boot back to inspect the connection between the box and harness.
Full disassembly and inspection of the distributor is highly recommended due to the intermittent nature of triggering problems. Pay special attention to the distributor trigger shielded cable ( green wire ), magnetic pulse generator magnet and magnetic pulse generator winding connection as these parts are known to fail in combination. An especially common problem is a broken magnet pole. Evidence of arching between the magnetic pulse generator magnet points indicates a defective rotor. In this case replace the rotor, magnetic pulse winding, green wire and ignition box. The Perma-Tune high performance triggering is so accurate that worn out distributor shaft bearings can be detected by the tachometer. This is indicated by the tachometer needle slightly bouncing at idle. Trigger signal problems can cause double triggering which results in a weak ignition spark. Due to the lower triggering resolution of the stock ignition box, some symptoms of trigger signal problems can be more evident after the Perma-Tune is installed. Refer to the vehicle maintenance manual for triggering signal wave form specifications and distributor repair instructions.
To quickly test the triggering circuit without the use of an oscilloscope: Unplug the harness connector from the ignition box. Refer to the 911SC Installation Instructions diagram, connect an Ohm meter between pins 3 and 6 of the harness connector. To prevent the possibility of misdiagnosis, tug on the green triggering signal wire located at the base of the distributor while viewing the meter. The published specification for the magnetic pulse generator is 600 Ohms +- 100. Our experience has shown that a variation of +- 25 Ohm indicates a need to repair defective connections or to replace the magnetic pulse generator windings.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

93060270200

The product you are viewing cross references to these numbers

Reconditioned Cabrio Folding Top Control Unit.

Genuine

Fits:
Porsche 993 1995-98 CABRIO

PLEASE NOTE:

• The surcharge for this reconditioned part will be refunded when the exchange unit is received and approved by us and the relevant manufacturer.
• Please note, surcharge refunds often take an average of 6 to 8 weeks to be approved by the manufacturer.
• Acceptance of the exchange part is at the manufacturer's discretion, based on the part being fit for reconditioning.
• All surcharges and exchanges are subject to our terms and conditions.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

993618313X

The product you are viewing cross references to these numbers

CDI ignition module Bluetooth Programming Dongle, fits with Perma Tune 3 pin and 6 Pin Cdi boxes.



Fits:
Porsche 911 1974-77
Porsche 911 1978-83
Porsche 930 3.3L 1978-89

The new generation ignition boxes make diagnostics easier. The controller monitors and runs diagnoses programs automatically and is read by two coloured LED function lights the are viewable from underneath the unit. The diagnoses can also be done via this Bluetooth programming dongle.

New Perma Tune unit.

For Bluetooth Installation Instruction CLICK HERE

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

90506

The product you are viewing cross references to these numbers

Ignition Starter box CDI (HKZ) Bluetooth Programming Cable, fits with Perma Tune 3 pin and 6 Pin Cdi boxes.



Fits:
Porsche 356 12V
Porsche 911 1974-77
Porsche 911 1978-83
Porsche 930 3.3L 1978-89

The 90502 USB Smart Wire allows you to customize your Perma-Tune Ignition module program. It plugs into the USB port of a computer and then installs itself automatically. It also powers up the module for programming with a single plug without having to connect anything else to the module. The programming software is downloaded from the internet, free, so the module settings can then be changed, saved and organized as text files.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

90502

The product you are viewing cross references to these numbers

Central Locking Control Unit.



Fits:
Porsche 911 1984-89
Porsche 964 1989-90
Porsche 928 1987-90
Porsche 944 1985-90
Porsche 944 Turbo >>1991

Diagram ref no 6

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

91161811302

The product you are viewing cross references to these numbers

Complete ignition harness for a 3 pin CD1/HK2 box.
Includes all connector boots, PVC sheathing, high grade automotive wire, flat braided ground cable and contacts per the original specifications. Compatible with cars up to 1973.

Fits:
Porsche 911 1965-73
Porsche 914/6 1971-75

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

91161205000

The product you are viewing cross references to these numbers

ECU - Exchange product for Engine 930.20 / 930.26
PORSCHE part no.: 911.618.111.18
Bosch part no.: 0 261 200 078

Fits:
Porsche 911 3.2L 1986-89

PLEASE NOTE:

• The surcharge for this reconditioned part will be refunded when the exchange unit is received and approved by us and the relevant manufacturer.
• Please note, surcharge refunds often take an average of 6 to 8 weeks to be approved by the manufacturer.
• Acceptance of the exchange part is at the manufacturer's discretion, based on the part being fit for reconditioning.
• All surcharges and exchanges are subject to our terms and conditions.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

911618111LX

The product you are viewing cross references to these numbers

ECU Porsche 911 3.2L 1986-89 Bosch 0261200078

PORSCHE part no.: 911.618.111.19
Bosch part no.: 0 261 200 078
Engine: 930.20 M240

Fits:
Porsche 911 3.2L 1986-89

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

91161811119

The product you are viewing cross references to these numbers

Ignition module. Porsche 356 or early 911 12 Volt or 8 Volt ignition cars.



Disclaimer: Before fitting this CDI unit please make sure the new PERMA-TUNE coil is being fitted with it. Do not try to start the car with Blue Bosch coil made in Brazil. This will damage the Perma-Tune CDI box and void the warranty. If CDI unit was not purchased with the PERMA-TUNE coil the warranty will not be respected. Fitting with other brand coils at your own risk.

Bluetooth programmable (Bluetooth Smart Wire required part no 90506)

Brand: Perma Tune
This is an upgrade for the ignition system. Basically it puts the load of the ignition system through the box rather than the distributor. You take the existing wiring and run it through this box and the points then become an earth trigger switch for the box rather than switching the coil.


This Model is the first of a brand new product line for Perma-Tune. We have combined our accumulated knowledge of Porsche ignition over the last 48 years and applied it to the very latest electronics technology to produce a state of the art electronic ignition module that is period correct looking. Made to look like an old school electrical relay, it blends right into the engine bay of a 356 or an early 911.

NO CRIMPS, NO MESS, NO HEADACHES
Plug and play features eliminate the need for wire crimps and complicated wiring diagrams. Wires are cut and stripped, then inserted into the wire bus for a secure, plug in connection without the need for special tools or wire crimps.

Simple, four wire installation. There is no need to interpret complicated wiring diagrams, the terminals are clearly marked so you know exactly where each wire goes.

NO DIALS, NO SWITCHES, NO PROBLEMS
Installation is easy. There are no dials to turn, no switches to set and no chips to plug in. The 356906 Perma-Tune comes to you pre-programmed and ready to be installed on a 356. You can always customise the module later using your wireless device to make secure, reliable configuration changes through the built in Bluetooth connection.

STRONG, YET FORGIVING
The Perma-Tune ignition module features on board diagnostics to help you install the module. The built in strobe light can help you check your ignition timing. It also has self resetting overload protection so there are no fuses to replace.

SMART CONNECTIONS
Use any kind of distributor you have. The Points distributor connection will work with breaker points or any aftermarket distributor.

The tachometer output connection is universal and will work with the stock tachometer or aftermarket electronic tachometer, shift light and RPM switch.

Power connects to 12 Volt or 8 Volt systems. Six Volt converters are not available at this time.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

356906

The product you are viewing cross references to these numbers

Ignition Starter box CDI 3 PIN.
(Bosch reference 227-200-001)


Classic Retrofit replacement CDI+ ignition offers you bespoke modern electronics in a standard looking package. The CDI+ unit requires no modifications to the original wiring harness or vehicle metalwork and is 'plug and play'.

The CDI+ is a direct replacement for the 3 pin and 6 pin Bosch units fitted to Porsche 911's between 1969 and 1983 (and turbo models to ~1988). All CDI+ units have a 48 MHz microprocessor onboard to control ignition timing.

Basic Unit:
The basic unit is a plug and play replacement for the Original Bosch CDI. It will work with the existing distributor without modification and still uses the weights and springs for the advance curve. It is pre-set at the factory (to your specification) and has the following features:
-Hard RPM limiter.
-Soft RPM limiter.
-Double spark at all RPMs
-Shift Light output
-Tacho calibration
-Upgradeable through firmware updates (at one of our specialists)
-The following parameters can be adjusted using the hidden 'jog wheel'.
-Hard RPM limiter.
-Soft RPM limiter.
-Shift light RPM.
-Tacho calibration.
The basic unit can be upgraded to an advanced unit at a later date by one of our specialists.

Advanced Unit:
The advanced unit allows the adjustment/tuning of the ignition advance curve and other features by plugging in a laptop. This can be achieved by 'overlaying' a curve on top of the distributor weights/springs curve or by locking the distributor and replacing the curve completely. Either way, you can unlock the true potential of your engine by adjusting fuelling and having the ignition curve to match.

The CDI+ has all the features of the basic unit but allow more flexibility in adjustment:
-Fully programmable ignition advance curve.
-Hard RPM limiter with adjustable ignition cut schemes
-Soft RPM limiter with adjustable ignition retard
-Launch RPM limiter
-Double spark at all RPMs
-Max RPM tell tale
-Shift Light output
-Clutch pedal input
-Tacho calibration
-Upgradeable through firmware updates

Fits:
Porsche 911 1965-77

For 911-CDI+ Ignition Manual CLICK HERE

For 911-CDI+ Dyno Test Results CLICK HERE

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

91160270700

The product you are viewing cross references to these numbers

Ignition Starter Unit CDI 6 PIN.
(Bosch Ref 0227300004)

Classic Retrofit replacement CDI+ ignition offers you bespoke modern electronics in a standard looking package. The CDI+ unit requires no modifications to the original wiring harness or vehicle metalwork and is 'plug and play'.

The CDI+ is a direct replacement for the 3 pin and 6 pin Bosch units fitted to Porsche 911's between 1969 and 1983 (and turbo models to ~1988). All CDI+ units have a 48 MHz microprocessor onboard to control ignition timing.

Advanced Unit:
The advanced unit allows the adjustment/tuning of the ignition advance curve and other features by plugging in a laptop. This can be achieved by 'overlaying' a curve on top of the distributor weights/springs curve or by locking the distributor and replacing the curve completely. Either way, you can unlock the true potential of your engine by adjusting fuelling and having the ignition curve to match.

The CDI+ has all the features of the basic unit but allow more flexibility in adjustment:
-Fully programmable ignition advance curve.
-Hard RPM limiter with adjustable ignition cut schemes
-Soft RPM limiter with adjustable ignition retard
-Launch RPM limiter
-Double spark at all RPMs
-Max RPM tell tale
-Shift Light output
-Clutch pedal input
-Tacho calibration
-Upgradeable through firmware updates

Fits:
Porsche 911 1978-83
Porsche 930 3.3L 1978-89

For 911-CDI+ Ignition Manual CLICK HERE

For 911-CDI+ Dyno Test Results CLICK HERE

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

93060270200

The product you are viewing cross references to these numbers