Enter your VAT number here and click Verify:
Your details have been verified. VAT number registered to:
,
.
Your order will now be zero rated for VAT purposes. We reserve the right to verify these details after your order request has been made and reinstate VAT if required.
Your VAT details were not recognised or were invalid. Your VAT number must be matched to your Billing Country as specified above. This is currently specified as . You do not need to enter the country code part of your VAT number as this has already been selected in your billing address details above.
The VAT number checking service is currently offline. Please supply your VAT details within the comments or special instructions field below and we will apply a VAT discount after placing your order request.
The OE MATCH Rear Boot Lid Hinge, Left is a replacement hinge designed to support, locate and guide the rear boot or engine lid through its opening and closing movement on compatible Porsche applications.
Fits:
- Porsche 911 1965-1968 2.0L / 912 SWB (F)
- Porsche 911 1968-1973 2.2L / 2.4L / 2.7L RS LWB (F)
- Porsche 911 1974-1977 2.7L / 1976-77 3.0 Carrera
- Porsche 911 1978-1983 3.0L / SC
- Porsche 911 1984-1986 3.2L
- Porsche 911 1987-1989 3.2L G50
- Porsche 911 1975-1977 3.0L Turbo (930)
- Porsche 911 1978-1989 3.3L Turbo (930)
Diagram Ref No 2
The hinge forms an important connection between the lid and vehicle body. Correct hinge condition is essential for smooth operation, accurate panel alignment and consistent shut-line gaps. A worn, bent or corroded hinge can cause the lid to sit incorrectly, become difficult to operate or make contact with surrounding bodywork.
What This Product Does:
The rear boot lid hinge provides the pivoting connection that allows the rear lid to open and close while remaining correctly located relative to the vehicle body.
Working with the corresponding hinge and associated lid hardware, it helps:
- Support the rear lid
- Provide a controlled pivot point
- Guide the lid during opening and closing
- Maintain correct panel positioning
- Maintain consistent body-panel gaps
- Help the lid align correctly with the latch
- Prevent unnecessary contact with surrounding bodywork
- Support smooth and predictable lid operation
Correct hinge geometry is particularly important because even a relatively small amount of wear or distortion can affect the position of the lid.
Symptoms Of Wear Or Failure:
Rear lid hinges can deteriorate through age, corrosion, repeated use, accident damage or excessive force being applied to the lid.
Common symptoms include:
- Rear lid sitting too high or too low
- Uneven panel gapsLid appearing twisted or misaligned
- Difficulty opening or closing the lid
- Lid requiring excessive force to close
- Poor alignment with the latch
- Binding or stiffness during movement
- Excessive movement or play at the hinge
- Squeaking or creaking
- Visible corrosion
- Bent or distorted hinge components
- Cracked or damaged mounting areas
- Lid rubbing against surrounding bodywork
If the lid has suffered previous impact damage, the hinge should be inspected even if the damage is not immediately obvious.
Why Replacement Matters:
Replacing a worn, bent or corroded rear boot lid hinge helps restore the correct movement and positioning of the lid.
Replacement can help:
- Restore smooth opening and closing
- Improve rear lid alignment
- Restore consistent panel gaps
- Improve latch engagement
- Reduce unwanted movement
- Prevent the lid rubbing against adjacent panels
- Reduce stress on the opposite hinge
- Protect surrounding paint and bodywork
- Restore the correct exterior appearance
Proper lid alignment is especially important on classic vehicles where panel fit and shut-line consistency contribute significantly to the overall appearance.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
91151203500
The product you are viewing cross references to these numbers
- Porsche 911 1965-1968 2.0L / 912 SWB (F)
- Porsche 911 1968-1973 2.2L / 2.4L / 2.7L RS LWB (F)
- Porsche 911 1974-1977 2.7L / 1976-77 3.0 Carrera
- Porsche 911 1978-1983 3.0L / SC
- Porsche 911 1984-1986 3.2L
- Porsche 911 1987-1989 3.2L G50
- Porsche 911 1975-1977 3.0L Turbo (930)
- Porsche 911 1978-1989 3.3L Turbo (930)

