后控制臂
1 kit required per axle
Fits
Porsche 986 Boxster - Front and Rear
Porsche 987 Boxster and Cayman - Front and Rear
Porsche 996 - Front and Rear
Porsche 997 - Front and Rear
Porsche 981 Boxster and Cayman -Front Only
Porsche 991 -Front Only
Caster Tuning
Our Caster Adjuster allows you to tune this important setting that the factory left out. A must-have for cars that have extended lower control arms (GT3 control arms or eccentric monoballs) to correct for un-intended caster change that is caused by the extended arms.
Caster is also a great tuning aid for adjusting out understeer. Our Caster Adjusters let you tune the caster you need.
Two eccentric mounting points increase range of adjustment by up to 25mm. Choose from the inner bore for minor caster adjustments or the outer bore for extreme adjustments.
Rear Weight Bias
For the rear suspension, our Caster Adjuster can reduce rear overhang and rear weight bias. Cars with aggressive rear camber actually draw the wheels forward, increasing rear weight bias. Use our Caster Adjuster to compensate and even over-compensate for less rear weight bias than stock
Maintain Proper Alignment
Our Caster Adjuster is solid aluminum to hold alignment settings precisely. Stock rubber bushings compress under load, allowing alignment to wander and making the car less predictable. Our solid design eliminates compression, improves precision and maintains geometry true.
Functional Design Built To Last
Available for factory type lower control arms (wishbones) front and rear, including stock type arms and GT3 arms
相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号,供比较之用。
2180011
您正在查看的产品与这些编号存在交叉引用关系
- Porsche Boxster 986 2.5L 1997-99
- Porsche Boxster 986 2.7L 1999-02
- Porsche Boxster S 986 3.2L 1999-02
- Porsche Boxster 986 2.7L 2003-04
- Porsche Boxster S 986 3.2L 2003-04
- Porsche Boxster 987 2.7L 2005 -08/08
- Porsche Boxster 987 S 3.2/3.4L 2005-08/08
- Porsche Boxster 987 MKII 2.9L 2009-2012
- Porsche Boxster S 987 MKII 3.4L 2009-2012
- Porsche Boxster 981 2.7L 2012-16
- Porsche Boxster S 981 3.4L 2012-16
- Porsche Boxster Spyder 3.8L 2016
- Porsche 996 C2 3.4L 1997-08/01
- Porsche 996 C4 3.4L 1997-08/01
- Porsche 996 C2 3.6L 09/01-2005
- Porsche 996 C4 3.6L 09/01-2005
- Porsche 996 C4S 3.6L 09/01-2005
- Porsche 996 TURBO 2000-05
- Porsche 996 GT2 2001-05
- Porsche 996 GT3 MKI 1999-02
- Porsche 996 GT3 MKII 2003>>
- Porsche 996 GT3 RS 2003-04
- Porsche 997 Carrera 2 3.6L 2005>>
- Porsche 997 Carrera 2S 3.8L 2005>>
- Porsche 997 Carrera 4 3.6L 2005>>
- Porsche 997 Carrera 4S 3.8L 2005>>
- Porsche 997 TURBO 2007>>
- Porsche 997 GT3 2007>>
- Porsche 997 GT2 2007>>
- Porsche 997 MKII Carrera C2 3.6L 2009>>
- Porsche 997 MKII Carrera C4 3.6L 2009>>
- Porsche 997 MKII Carrera C2S 3.8L 2009>>
- Porsche 997 MKII Carrera C4S 3.8L 2009>>
- Porsche 997 MKII GT3 2010>>
- Porsche 997 MKII Turbo 2009>>
- Porsche 997 MKII GT2 RS 2011>>
- Porsche 991 Carrera C2 3.4L (350Bhp)
- Porsche 991 Carrera C2S 3.8L (400Bhp)
- Porsche 991 Carrera C4 3.4L (350Bhp)
- Porsche 991 Carrera C4S 3.8L (400Bhp)
- Porsche 991 Turbo 3.8L (520bhp)
- Porsche 991 Turbo S 3.8L (560Bhp)
- Porsche 991 R 4.0L (500 Bhp)
- Porsche 991 GT3 3.8L (475Bhp)
- Porsche 991 GT3 RS 4.0L (500Bhp)
- Porsche 991 Carrera 2 3.0L (370 Bhp)
- Porsche 991 Carrera 2S 3.0L (420 Bhp)
- Porsche 991 Carrera 4 3.0L (370 Bhp)
- Porsche 991 Carrera 4S 3.0L (420 Bhp)
- Porsche 991 Cabriolet 2 3.0L (370 Bhp)
- Porsche 991 Cabriolet 2S 3.0L (420 Bhp)
- Porsche 991 Cabriolet 4 3.0L (370 Bhp)
- Porsche 991 Cabriolet 4S 3.0L (420 Bhp)
- Porsche 991 Targa 4 3.0L (370 Bhp)
- Porsche 991 Targa 4S 3.0L (420 Bhp)
- Porsche 991 Turbo Coupe 3.8L (540 Bhp)
- Porsche 991 Turbo S Coupe 3.8L (580 Bhp)
- Porsche 991 Turbo Cabriolet 3.8L (540 Bhp)
- Porsche 991 Turbo S Cabriolet 3.8L (580 Bhp)
- Porsche Cayman 2.7L 987C 2006-08
- Porsche Cayman S 3.4L 987C 2005-08
- Porsche Cayman 2.9L 987C MKII 2009-12
- Porsche Cayman S / R 3.4L 987C MKII 2009-12
- Porsche Cayman 2.7L 981 2013-16
- Porsche Cayman S 3.4L 981 2013-16
- Porsche Cayman GT4 3.8L 2015-16
Fits
Porsche 986 Boxster - Front and Rear
Porsche 996, 997 - Front and Rear
Porsche 991 - Front Only
Porsche 987 Boxster and Cayman - Front and Rear
Porsche 981 Boxster and Cayman - Front and Rear
Porsche 718 Boxster and Cayman - Front and Rear
Set of 2 x Adjustable lower control arms - 1 pair, required per axle
Elephant Racing adjustable lower control arms provide the camber, caster and precision you need. Length adjustable similar to the factory GT3 control arms, but without the need for shims.
Quick and Easy Adjustments – No need to keep a stock of shims on hand, length is easily adjusted by rotating the center hex head. Rotate clockwise to expand or counter-clockwise to contract the arm length.Adjustments can be made within minutes. No shims to mess with. Perfect setup to make quick changes for the track.
Widen Track – Use in combination with our camber plates on the front, or our adjustable length arms upper control arms on the rear to widen the track. This allows you to achieve a wider track without altering the scrub radius as happens when using wheel spacers.
Heim Joint – Our spherical bearings eliminate the deflection associated with rubber bushings. These bearings maintain stable suspension alignment, and improve feedback.
Fully Weather Sealed – Proper boots at both the ball joint and heim joint ends to keep water and contaminants out for extended life. These arms are suitable for extended road and track use.
Camber Adjustment – Extended range of adjustment lets you achieve aggressive camber. Or you can dial it back to get a factory street alignment on lowered cars.
Caster Adjustment – Our Caster Adjuster allows you to tune this important setting that the factory left out. A must-have for cars that have extended lower control arms to correct for un-intended caster change that is caused by the extended arms. Rotate the center puck and bolt down to secure the setting.
The arms are fully rebuildable with replaceable heim and ball joints.
On 996, 997, & 991 Cars:
Center puck can be also used as a wheelbase adjuster on the rear to draw the wheels back to improve weight distribution. It is a great tuning aid for adjusting out understeer
Litronic Bracket – This bracket is required for cars that are originally equipped with the litronic headlights. This adapter bracket attaches to the headlight angle sensor.
相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号,供比较之用。
2180001
您正在查看的产品与这些编号存在交叉引用关系
- Porsche Boxster 986 2.5L 1997-99
- Porsche Boxster 986 2.7L 1999-02
- Porsche Boxster S 986 3.2L 1999-02
- Porsche Boxster 986 2.7L 2003-04
- Porsche Boxster S 986 3.2L 2003-04
- Porsche Boxster 987 2.7L 2005 -08/08
- Porsche Boxster 987 S 3.2/3.4L 2005-08/08
- Porsche Boxster 987 MKII 2.9L 2009-2012
- Porsche Boxster S 987 MKII 3.4L 2009-2012
- Porsche Boxster 981 2.7L 2012-16
- Porsche Boxster S 981 3.4L 2012-16
- Porsche Boxster Spyder 3.8L 2016
- Porsche Boxster 718 2.0L Manual (300 Bhp)
- Porsche Boxster 718 2.0L PDK (300 Bhp)
- Porsche Boxster S 718 2.5L Manual (350 Bhp)
- Porsche Boxster S 718 2.5L PDK (350 Bhp)
- Porsche Boxster T 718 2.0L Manual (300 Bhp)
- Porsche Boxster T 718 2.0L PDK (300 Bhp)
- Porsche Boxster GTS 718 2.5L Manual (365 Bhp)
- Porsche Boxster GTS 718 2.5L PDK (365 Bhp)
- Porsche Boxster GTS 718 4.0L Manual (400 Bhp)
- Porsche Boxster GTS 718 4.0L PDK (400 Bhp)
- Porsche Boxster Spyder 718 4.0L (420 Bhp)
- Porsche Boxster 25 Years 718 4.0L Manual (400 Bhp)
- Porsche Boxster 25 Years 718 4.0L PDK (400 Bhp)
- Porsche 996 C2 3.4L 1997-08/01
- Porsche 996 C4 3.4L 1997-08/01
- Porsche 996 C2 3.6L 09/01-2005
- Porsche 996 C4 3.6L 09/01-2005
- Porsche 996 C4S 3.6L 09/01-2005
- Porsche 996 TURBO 2000-05
- Porsche 996 GT2 2001-05
- Porsche 996 GT3 MKI 1999-02
- Porsche 996 GT3 MKII 2003>>
- Porsche 996 GT3 RS 2003-04
- Porsche 997 Carrera 2 3.6L 2005>>
- Porsche 997 Carrera 2S 3.8L 2005>>
- Porsche 997 Carrera 4 3.6L 2005>>
- Porsche 997 Carrera 4S 3.8L 2005>>
- Porsche 997 TURBO 2007>>
- Porsche 997 GT3 2007>>
- Porsche 997 GT2 2007>>
- Porsche 997 MKII Carrera C2 3.6L 2009>>
- Porsche 997 MKII Carrera C4 3.6L 2009>>
- Porsche 997 MKII Carrera C2S 3.8L 2009>>
- Porsche 997 MKII Carrera C4S 3.8L 2009>>
- Porsche 997 MKII GT3 2010>>
- Porsche 997 MKII Turbo 2009>>
- Porsche 997 MKII GT2 RS 2011>>
- Porsche 991 Carrera C2 3.4L (350Bhp)
- Porsche 991 Carrera C2S 3.8L (400Bhp)
- Porsche 991 Carrera C4 3.4L (350Bhp)
- Porsche 991 Carrera C4S 3.8L (400Bhp)
- Porsche 991 Turbo 3.8L (520bhp)
- Porsche 991 Turbo S 3.8L (560Bhp)
- Porsche 991 R 4.0L (500 Bhp)
- Porsche 991 GT3 3.8L (475Bhp)
- Porsche 991 GT3 RS 4.0L (500Bhp)
- Porsche 991 Carrera 2 3.0L (370 Bhp)
- Porsche 991 Carrera 2S 3.0L (420 Bhp)
- Porsche 991 Carrera 4 3.0L (370 Bhp)
- Porsche 991 Carrera 4S 3.0L (420 Bhp)
- Porsche 991 Cabriolet 2 3.0L (370 Bhp)
- Porsche 991 Cabriolet 2S 3.0L (420 Bhp)
- Porsche 991 Cabriolet 4 3.0L (370 Bhp)
- Porsche 991 Cabriolet 4S 3.0L (420 Bhp)
- Porsche 991 Targa 4 3.0L (370 Bhp)
- Porsche 991 Targa 4S 3.0L (420 Bhp)
- Porsche 991 Turbo Coupe 3.8L (540 Bhp)
- Porsche 991 Turbo S Coupe 3.8L (580 Bhp)
- Porsche 991 Turbo Cabriolet 3.8L (540 Bhp)
- Porsche 991 Turbo S Cabriolet 3.8L (580 Bhp)
- Porsche 991 Speedster 4.0L (510Bhp)
- Porsche 991 GT3 4.0L (500 Bhp) / GT3 RS 4.0L (520 Bhp)
- Porsche 991 GT2 RS 3.8L PDK (700 bhp)
- Porsche Cayman 2.7L 987C 2006-08
- Porsche Cayman S 3.4L 987C 2005-08
- Porsche Cayman 2.9L 987C MKII 2009-12
- Porsche Cayman S / R 3.4L 987C MKII 2009-12
- Porsche Cayman 2.7L 981 2013-16
- Porsche Cayman S 3.4L 981 2013-16
- Porsche Cayman GT4 3.8L 2015-16
- Porsche Cayman 718 2.0L Manual (300Bhp)
- Porsche Cayman 718 2.0L PDK (300Bhp)
- Porsche Cayman S 718 2.5L Manual (350Bhp)
- Porsche Cayman S 718 2.5L PDK (350Bhp)
- Porsche Cayman T 718 2.0L Manual (300Bhp)
- Porsche Cayman T 718 2.0L PDK (300 Bhp)
- Porsche Cayman GTS 718 2.5L Manual (365 Bhp)
- Porsche Cayman GTS 718 2.5L PDK (365 Bhp)
- Porsche Cayman GTS 718 4.0L Manual (400 Bhp)
- Porsche Cayman GTS 718 4.0L PDK (400 Bhp)
- Porsche Cayman GT4 718 4.0L / GT4 RS 718 4.0L
1 pair required per car
Fits
Porsche 991 2012 Onward - Rear Only
We've developed 991 Rear Adjustable Wishbone to provide the camber and precision you need. Machined from billet aluminum, hard anodized and fully weather sealed, this arms are strong enough for track and durable enough for extended street use.
Easy Camber Adjustment – The double adjuster makes fast and precise camber changes in minutes. Dialing in your race car, or adding camber for the occasional track day is now a simple operation.
Camber Range – Extended range of adjustment lets you get aggressive camber. Or you can dial it back to get a factory street alignment on lowered cars.
Porsche 991 adjustable rear lower wishbone detail
Heim Joint – Eliminate suspension deflection associated with rubber compression. For superior driving precision, spherical bearing type heim joints are used instead of the rubber bushings that are found in OEM control arms. The arms are fully rebuildable with replaceable heim joints.
Fully Weather Sealed – Rubber boot protects the heim joint to keep water and contaminant out for extended life.
The kit includes both rear lower wishbones. Order one kit per car
相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号,供比较之用。
2180012
您正在查看的产品与这些编号存在交叉引用关系
- Porsche 991 Carrera C2 3.4L (350Bhp)
- Porsche 991 Carrera C2S 3.8L (400Bhp)
- Porsche 991 Carrera C4 3.4L (350Bhp)
- Porsche 991 Carrera C4S 3.8L (400Bhp)
- Porsche 991 Turbo 3.8L (520bhp)
- Porsche 991 Turbo S 3.8L (560Bhp)
- Porsche 991 Carrera 2 3.0L (370 Bhp)
- Porsche 991 Carrera 2S 3.0L (420 Bhp)
- Porsche 991 Carrera 4 3.0L (370 Bhp)
- Porsche 991 Carrera 4S 3.0L (420 Bhp)
- Porsche 991 Cabriolet 2 3.0L (370 Bhp)
- Porsche 991 Cabriolet 2S 3.0L (420 Bhp)
- Porsche 991 Cabriolet 4 3.0L (370 Bhp)
- Porsche 991 Cabriolet 4S 3.0L (420 Bhp)
- Porsche 991 Targa 4 3.0L (370 Bhp)
- Porsche 991 Targa 4S 3.0L (420 Bhp)
- Porsche 991 Turbo Coupe 3.8L (540 Bhp)
- Porsche 991 Turbo S Coupe 3.8L (580 Bhp)
- Porsche 991 Turbo Cabriolet 3.8L (540 Bhp)
- Porsche 991 Turbo S Cabriolet 3.8L (580 Bhp)
with adjustable caster puck.
Fits:
Porsche 991 Front Only (Does Not Fit 991 GT3)
Porsche 992 Front Only (Does Not Fit 992 GT3)
Porsche 981 Front And Rear
GT3 Lower Control Arms (LCA)
992 GT3 cars are equipped with a special front GT3 control arm that is two-piece and length-adjustable by fitting shims between the halves. The changeable length allows for aggressive camber settings and track width adjustment, increasing cornering grip and performance.
Unfortunately the stock 992 GT3 control arm cannot be fit to a non-GT3 992 because the ball joint end is completely different.
That’s why we created these GT3 type front lower control arms to fit the 992 C2, C4 and Turbo cars.
Our GT3 ERX LCAs for the 922 provides the same type front camber and track width adjustment for non-GT3 992 cars.
The GT3 ERX lower control arm is a system built up of three component parts, each ordered separately:
– GT3 ERX adjustable outer lower control arm
– GT3 adjustable inner lower control arm
– GT3 lower control arms shims (various thicknesses, stackable)
GT3 ERX Front Outer Lower Control Arms
Elephant Racing has developed an upgraded GT3 type front lower control arm for the non-GT3 992 cars. Our GT3 type arms have the correct ball joint style for fitment to 992 C2, C4 and Turbo cars. They do not fit 992 GT3 cars.
Like the factory lower control arms, the Elephant Racing outer arm has an integrated ball joint that is weather sealed. Unlike the factory lower control arms, the ball joint in the Elephant Racing arms is rebuildable and we offer the rebuild kit allowing you to renew the arm when needed.
The GT3 ERX LCAs have features to accept the factory height sensor and air deflectors.
The outer arms are sold as a left and right side pair, to be combined with our GT3 inner lower control arms – orderable separately.
These can be paired with a choice of GT3 lower control arms inner:
– Elephant Racing GT3 lower control arm inner rubber bushing
– Elephant Racing GT3 lower control arm inner spherical bearing
相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号,供比较之用。
2180044
您正在查看的产品与这些编号存在交叉引用关系
- Porsche Boxster 981 2.7L 2012-16
- Porsche Boxster S 981 3.4L 2012-16
- Porsche 991 Carrera C2 3.4L (350Bhp)
- Porsche 991 Carrera C2S 3.8L (400Bhp)
- Porsche 991 Carrera C4 3.4L (350Bhp)
- Porsche 991 Carrera C4S 3.8L (400Bhp)
- Porsche 991 Turbo 3.8L (520bhp)
- Porsche 991 Turbo S 3.8L (560Bhp)
- Porsche 991 Carrera 2 3.0L (370 Bhp)
- Porsche 991 Carrera 2S 3.0L (420 Bhp)
- Porsche 991 Carrera 4 3.0L (370 Bhp)
- Porsche 991 Carrera 4S 3.0L (420 Bhp)
- Porsche 991 Cabriolet 2 3.0L (370 Bhp)
- Porsche 991 Cabriolet 2S 3.0L (420 Bhp)
- Porsche 991 Cabriolet 4 3.0L (370 Bhp)
- Porsche 991 Cabriolet 4S 3.0L (420 Bhp)
- Porsche 991 Targa 4 3.0L (370 Bhp)
- Porsche 991 Targa 4S 3.0L (420 Bhp)
- Porsche 991 Turbo Coupe 3.8L (540 Bhp)
- Porsche 991 Turbo S Coupe 3.8L (580 Bhp)
- Porsche 991 Turbo Cabriolet 3.8L (540 Bhp)
- Porsche 991 Turbo S Cabriolet 3.8L (580 Bhp)
- Porsche 992 Carrera 2 3.0L
- Porsche 992 Carrera 4 3.0L
- Porsche 992 Carrera 2 Cabriolet 3.0L
- Porsche 992 Carrera 4 Cabriolet 3.0L
- Porsche 992 Carrera 2S 3.0L
- Porsche 992 Carrera 4S 3.0L
- Porsche 992 Carrera 2S Cabriolet 3.0L
- Porsche 992 Carrera 4S Cabriolet 3.0L
- Porsche 992 Targa 4 3.0L
- Porsche 992 Targa 4S 3.0L
- Porsche 992 Speedster 4.0L
- Porsche 992 Turbo 3.8L
- Porsche 992 Turbo S 3.8L
- Porsche 992 Turbo Cabriolet 3.8L
- Porsche 992 Turbo S Cabriolet 3.8L
- Porsche Cayman 2.7L 981 2013-16
- Porsche Cayman S 3.4L 981 2013-16
Fits:
Porsche 996, 997, 991, 992 W/ GT3 Style Control Arms (Front/Rear),
Porsche Boxster, Cayman 1999>> W/ GT3 Style Control Arms (Front Only)
Elephant Racing has developed GT3 type inner lower control arms.
These are readily available and dimensionally identical to the factory parts. They can be mix-matched with the factory type inner/outer lower control arm and shims.
The Elephant Racing inner arm is offered in two flavors, GT3 Street Inner Lower Control Arm and GT3 Cup Inner Lower Control Arm. GT3 street is equipped with a rubber bushed central bushing and the GT3 Cup is equipped with a solid caster adjustable central bushing.
Our GT3 Street Inner Lower Control Arm has sport-hardness rubber bushings to provide upgraded control and driver feedback while still offering good road noise isolation.
Our GT3 Cup Inner Lower Control Arms uses weather sealed spherical bearings. These deliver superior precision, control, and performance. They will transmit a bit more road noise than rubber bushings.
These can be paired with a choice of GT3 outer control lower arms:
– Elephant Racing GT3 Street Outer Lower Control Arms
– Elephant Racing GT3 Cup Outer Lower Control Arms
– Factory GT3 Street Outer Lower Control Arms
相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号,供比较之用。
2180039
您正在查看的产品与这些编号存在交叉引用关系
- Porsche Boxster 986 2.5L 1997-99
- Porsche Boxster 986 2.7L 1999-02
- Porsche Boxster S 986 3.2L 1999-02
- Porsche Boxster 986 2.7L 2003-04
- Porsche Boxster S 986 3.2L 2003-04
- Porsche Boxster 987 2.7L 2005 -08/08
- Porsche Boxster 987 S 3.2/3.4L 2005-08/08
- Porsche Boxster 987 MKII 2.9L 2009-2012
- Porsche Boxster S 987 MKII 3.4L 2009-2012
- Porsche Boxster 718 2.0L Manual (300 Bhp)
- Porsche Boxster 718 2.0L PDK (300 Bhp)
- Porsche Boxster S 718 2.5L Manual (350 Bhp)
- Porsche Boxster S 718 2.5L PDK (350 Bhp)
- Porsche Boxster T 718 2.0L Manual (300 Bhp)
- Porsche Boxster T 718 2.0L PDK (300 Bhp)
- Porsche Boxster GTS 718 2.5L Manual (365 Bhp)
- Porsche Boxster GTS 718 2.5L PDK (365 Bhp)
- Porsche Boxster GTS 718 4.0L Manual (400 Bhp)
- Porsche Boxster GTS 718 4.0L PDK (400 Bhp)
- Porsche Boxster Spyder 718 4.0L (420 Bhp)
- Porsche Boxster 25 Years 718 4.0L Manual (400 Bhp)
- Porsche Boxster 25 Years 718 4.0L PDK (400 Bhp)
- Porsche 996 C2 3.4L 1997-08/01
- Porsche 996 C4 3.4L 1997-08/01
- Porsche 996 C2 3.6L 09/01-2005
- Porsche 996 C4 3.6L 09/01-2005
- Porsche 996 C4S 3.6L 09/01-2005
- Porsche 996 TURBO 2000-05
- Porsche 996 GT2 2001-05
- Porsche 996 GT3 MKI 1999-02
- Porsche 996 GT3 MKII 2003>>
- Porsche 996 GT3 RS 2003-04
- Porsche 997 Carrera 2 3.6L 2005>>
- Porsche 997 Carrera 2S 3.8L 2005>>
- Porsche 997 Carrera 4 3.6L 2005>>
- Porsche 997 Carrera 4S 3.8L 2005>>
- Porsche 997 TURBO 2007>>
- Porsche 997 GT3 2007>>
- Porsche 997 GT2 2007>>
- Porsche 997 MKII Carrera C2 3.6L 2009>>
- Porsche 997 MKII Carrera C4 3.6L 2009>>
- Porsche 997 MKII Carrera C2S 3.8L 2009>>
- Porsche 997 MKII Carrera C4S 3.8L 2009>>
- Porsche 997 MKII GT3 2010>>
- Porsche 997 MKII Turbo 2009>>
- Porsche 997 MKII GT2 RS 2011>>
- Porsche 991 Carrera C2 3.4L (350Bhp)
- Porsche 991 Carrera C2S 3.8L (400Bhp)
- Porsche 991 Carrera C4 3.4L (350Bhp)
- Porsche 991 Carrera C4S 3.8L (400Bhp)
- Porsche 991 Turbo 3.8L (520bhp)
- Porsche 991 Turbo S 3.8L (560Bhp)
- Porsche 991 Carrera 2 3.0L (370 Bhp)
- Porsche 991 Carrera 2S 3.0L (420 Bhp)
- Porsche 991 Carrera 4 3.0L (370 Bhp)
- Porsche 991 Carrera 4S 3.0L (420 Bhp)
- Porsche 991 Cabriolet 2 3.0L (370 Bhp)
- Porsche 991 Cabriolet 2S 3.0L (420 Bhp)
- Porsche 991 Cabriolet 4 3.0L (370 Bhp)
- Porsche 991 Cabriolet 4S 3.0L (420 Bhp)
- Porsche 991 Targa 4 3.0L (370 Bhp)
- Porsche 991 Targa 4S 3.0L (420 Bhp)
- Porsche 991 Turbo Coupe 3.8L (540 Bhp)
- Porsche 991 Turbo S Coupe 3.8L (580 Bhp)
- Porsche 991 Turbo Cabriolet 3.8L (540 Bhp)
- Porsche 991 Turbo S Cabriolet 3.8L (580 Bhp)
- Porsche 992 Carrera 2 3.0L
- Porsche 992 Carrera 4 3.0L
- Porsche 992 Carrera 2 Cabriolet 3.0L
- Porsche 992 Carrera 4 Cabriolet 3.0L
- Porsche 992 Carrera 2S 3.0L
- Porsche 992 Carrera 4S 3.0L
- Porsche 992 Carrera 2S Cabriolet 3.0L
- Porsche 992 Carrera 4S Cabriolet 3.0L
- Porsche 992 Targa 4 3.0L
- Porsche 992 Targa 4S 3.0L
- Porsche 992 Speedster 4.0L
- Porsche 992 Turbo 3.8L
- Porsche 992 Turbo S 3.8L
- Porsche 992 Turbo Cabriolet 3.8L
- Porsche 992 Turbo S Cabriolet 3.8L
- Porsche Cayman 2.7L 987C 2006-08
- Porsche Cayman S 3.4L 987C 2005-08
- Porsche Cayman 2.9L 987C MKII 2009-12
- Porsche Cayman S / R 3.4L 987C MKII 2009-12
- Porsche Cayman 2.7L 981 2013-16
- Porsche Cayman S 3.4L 981 2013-16
- Porsche Cayman 718 2.0L Manual (300Bhp)
- Porsche Cayman 718 2.0L PDK (300Bhp)
- Porsche Cayman S 718 2.5L Manual (350Bhp)
- Porsche Cayman S 718 2.5L PDK (350Bhp)
- Porsche Cayman T 718 2.0L Manual (300Bhp)
- Porsche Cayman T 718 2.0L PDK (300 Bhp)
- Porsche Cayman GTS 718 2.5L Manual (365 Bhp)
- Porsche Cayman GTS 718 2.5L PDK (365 Bhp)
- Porsche Cayman GTS 718 4.0L Manual (400 Bhp)
- Porsche Cayman GTS 718 4.0L PDK (400 Bhp)
Fits
Porsche 996 - Front & Rear with Litronic headlights
Porsche 997 - Front & Rear with Litronic headlights
Porsche 991 - Front & Rear with Litronic headlights
Porsche 986 - Front Only with Litronic headlights
Porsche 987 - Front Only with Litronic headlights
Porsche 981 - Front Only with Litronic headlights,
Price is for 1 and 2 Required per axle
This bracket is required for cars that are originally equipped with the Litronic headlights. This adapter bracket attaches to the headlight angle sensor.
相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号,供比较之用。
2180009
您正在查看的产品与这些编号存在交叉引用关系
- Porsche Boxster 986 2.5L 1997-99
- Porsche Boxster 986 2.7L 1999-02
- Porsche Boxster S 986 3.2L 1999-02
- Porsche Boxster 986 2.7L 2003-04
- Porsche Boxster S 986 3.2L 2003-04
- Porsche Boxster 987 2.7L 2005 -08/08
- Porsche Boxster 987 S 3.2/3.4L 2005-08/08
- Porsche Boxster 987 MKII 2.9L 2009-2012
- Porsche Boxster S 987 MKII 3.4L 2009-2012
- Porsche Boxster 981 2.7L 2012-16
- Porsche Boxster S 981 3.4L 2012-16
- Porsche Boxster Spyder 3.8L 2016
- Porsche 996 C2 3.4L 1997-08/01
- Porsche 996 C4 3.4L 1997-08/01
- Porsche 996 C2 3.6L 09/01-2005
- Porsche 996 C4 3.6L 09/01-2005
- Porsche 996 C4S 3.6L 09/01-2005
- Porsche 996 TURBO 2000-05
- Porsche 996 GT2 2001-05
- Porsche 996 GT3 MKI 1999-02
- Porsche 996 GT3 MKII 2003>>
- Porsche 996 GT3 RS 2003-04
- Porsche 997 Carrera 2 3.6L 2005>>
- Porsche 997 Carrera 2S 3.8L 2005>>
- Porsche 997 Carrera 4 3.6L 2005>>
- Porsche 997 Carrera 4S 3.8L 2005>>
- Porsche 997 TURBO 2007>>
- Porsche 997 GT3 2007>>
- Porsche 997 GT2 2007>>
- Porsche 997 MKII Carrera C2 3.6L 2009>>
- Porsche 997 MKII Carrera C4 3.6L 2009>>
- Porsche 997 MKII Carrera C2S 3.8L 2009>>
- Porsche 997 MKII Carrera C4S 3.8L 2009>>
- Porsche 997 MKII GT3 2010>>
- Porsche 997 MKII Turbo 2009>>
- Porsche 997 MKII GT2 RS 2011>>
- Porsche 991 Carrera C2 3.4L (350Bhp)
- Porsche 991 Carrera C2S 3.8L (400Bhp)
- Porsche 991 Carrera C4 3.4L (350Bhp)
- Porsche 991 Carrera C4S 3.8L (400Bhp)
- Porsche 991 Turbo 3.8L (520bhp)
- Porsche 991 Turbo S 3.8L (560Bhp)
- Porsche 991 R 4.0L (500 Bhp)
- Porsche 991 GT3 3.8L (475Bhp)
- Porsche 991 GT3 RS 4.0L (500Bhp)
- Porsche 991 Carrera 2 3.0L (370 Bhp)
- Porsche 991 Carrera 2S 3.0L (420 Bhp)
- Porsche 991 Carrera 4 3.0L (370 Bhp)
- Porsche 991 Carrera 4S 3.0L (420 Bhp)
- Porsche 991 Cabriolet 2 3.0L (370 Bhp)
- Porsche 991 Cabriolet 2S 3.0L (420 Bhp)
- Porsche 991 Cabriolet 4 3.0L (370 Bhp)
- Porsche 991 Cabriolet 4S 3.0L (420 Bhp)
- Porsche 991 Targa 4 3.0L (370 Bhp)
- Porsche 991 Targa 4S 3.0L (420 Bhp)
- Porsche 991 Turbo Coupe 3.8L (540 Bhp)
- Porsche 991 Turbo S Coupe 3.8L (580 Bhp)
- Porsche 991 Turbo Cabriolet 3.8L (540 Bhp)
- Porsche 991 Turbo S Cabriolet 3.8L (580 Bhp)
- Porsche 991 Speedster 4.0L (510Bhp)
- Porsche 991 GT3 4.0L (500 Bhp) / GT3 RS 4.0L (520 Bhp)
- Porsche 991 GT2 RS 3.8L PDK (700 bhp)
- Porsche Cayman 2.7L 987C 2006-08
- Porsche Cayman S 3.4L 987C 2005-08
- Porsche Cayman 2.9L 987C MKII 2009-12
- Porsche Cayman S / R 3.4L 987C MKII 2009-12
- Porsche Cayman 2.7L 981 2013-16
- Porsche Cayman S 3.4L 981 2013-16
- Porsche Cayman GT4 3.8L 2015-16
Fits
Porsche 987 - Rear with Litronic headlights
Porsche 981 - Rear with Litronic headlights
Price is for 1 and 2 Required per axle
This bracket is required for cars that are originally equipped with the Litronic headlights. This adapter bracket attaches to the headlight angle sensor.
相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号,供比较之用。
218002
您正在查看的产品与这些编号存在交叉引用关系
- Porsche Boxster 986 2.5L 1997-99
- Porsche Boxster 986 2.7L 1999-02
- Porsche Boxster S 986 3.2L 1999-02
- Porsche Boxster 986 2.7L 2003-04
- Porsche Boxster S 986 3.2L 2003-04
- Porsche Boxster 987 2.7L 2005 -08/08
- Porsche Boxster 987 S 3.2/3.4L 2005-08/08
- Porsche Boxster 987 MKII 2.9L 2009-2012
- Porsche Boxster S 987 MKII 3.4L 2009-2012
- Porsche Boxster 981 2.7L 2012-16
- Porsche Boxster S 981 3.4L 2012-16
- Porsche Boxster Spyder 3.8L 2016
- Porsche 996 C2 3.4L 1997-08/01
- Porsche 996 C4 3.4L 1997-08/01
- Porsche 996 C2 3.6L 09/01-2005
- Porsche 996 C4 3.6L 09/01-2005
- Porsche 996 C4S 3.6L 09/01-2005
- Porsche 996 TURBO 2000-05
- Porsche 996 GT2 2001-05
- Porsche 996 GT3 MKI 1999-02
- Porsche 996 GT3 MKII 2003>>
- Porsche 996 GT3 RS 2003-04
- Porsche 997 Carrera 2 3.6L 2005>>
- Porsche 997 Carrera 2S 3.8L 2005>>
- Porsche 997 Carrera 4 3.6L 2005>>
- Porsche 997 Carrera 4S 3.8L 2005>>
- Porsche 997 TURBO 2007>>
- Porsche 997 GT3 2007>>
- Porsche 997 GT2 2007>>
- Porsche 997 MKII Carrera C2 3.6L 2009>>
- Porsche 997 MKII Carrera C4 3.6L 2009>>
- Porsche 997 MKII Carrera C2S 3.8L 2009>>
- Porsche 997 MKII Carrera C4S 3.8L 2009>>
- Porsche 997 MKII GT3 2010>>
- Porsche 997 MKII Turbo 2009>>
- Porsche 997 MKII GT2 RS 2011>>
- Porsche 991 Carrera C2 3.4L (350Bhp)
- Porsche 991 Carrera C2S 3.8L (400Bhp)
- Porsche 991 Carrera C4 3.4L (350Bhp)
- Porsche 991 Carrera C4S 3.8L (400Bhp)
- Porsche 991 Turbo 3.8L (520bhp)
- Porsche 991 Turbo S 3.8L (560Bhp)
- Porsche 991 R 4.0L (500 Bhp)
- Porsche 991 GT3 3.8L (475Bhp)
- Porsche 991 GT3 RS 4.0L (500Bhp)
- Porsche 991 Carrera 2 3.0L (370 Bhp)
- Porsche 991 Carrera 2S 3.0L (420 Bhp)
- Porsche 991 Carrera 4 3.0L (370 Bhp)
- Porsche 991 Carrera 4S 3.0L (420 Bhp)
- Porsche 991 Cabriolet 2 3.0L (370 Bhp)
- Porsche 991 Cabriolet 2S 3.0L (420 Bhp)
- Porsche 991 Cabriolet 4 3.0L (370 Bhp)
- Porsche 991 Cabriolet 4S 3.0L (420 Bhp)
- Porsche 991 Targa 4 3.0L (370 Bhp)
- Porsche 991 Targa 4S 3.0L (420 Bhp)
- Porsche 991 Turbo Coupe 3.8L (540 Bhp)
- Porsche 991 Turbo S Coupe 3.8L (580 Bhp)
- Porsche 991 Turbo Cabriolet 3.8L (540 Bhp)
- Porsche 991 Turbo S Cabriolet 3.8L (580 Bhp)
- Porsche 991 Speedster 4.0L (510Bhp)
- Porsche 991 GT3 4.0L (500 Bhp) / GT3 RS 4.0L (520 Bhp)
- Porsche 991 GT2 RS 3.8L PDK (700 bhp)
- Porsche Cayman 2.7L 987C 2006-08
- Porsche Cayman S 3.4L 987C 2005-08
- Porsche Cayman 2.9L 987C MKII 2009-12
- Porsche Cayman S / R 3.4L 987C MKII 2009-12
- Porsche Cayman 2.7L 981 2013-16
- Porsche Cayman S 3.4L 981 2013-16
- Porsche Cayman GT4 3.8L 2015-16
1 x tool required
Fits
Porsche 986 Boxster - Front and Rear
Porsche 987 Boxster and Cayman - Front and Rear
Porsche 996 - Front and Rear
Porsche 997 - Front and Rear
Porsche 981 Boxster and Cayman -Front Only
Porsche 991 -Front Only
Simplify the installation process of Monoball products and replacement bushings.
Our two piece cup and piston tools allow for simple bushing extraction and insertion without removal of the wheel carriers or control arms. No need to use a shop press. The tools are designed to precisely fit the bushing circumference, preventing accidental damage to the bushing and ensuring proper installation.
We have tools for the LCA central bushings, the rear upright LCA bushings, and the rear upright shock mount bushings.
Front and rear control arms on the 996, 997, 986, 987, & 981
Front Lower Control Arm only on 991
相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号,供比较之用。
2260019
您正在查看的产品与这些编号存在交叉引用关系
- Porsche Boxster 986 2.5L 1997-99
- Porsche Boxster 986 2.7L 1999-02
- Porsche Boxster S 986 3.2L 1999-02
- Porsche Boxster 986 2.7L 2003-04
- Porsche Boxster S 986 3.2L 2003-04
- Porsche Boxster 987 2.7L 2005 -08/08
- Porsche Boxster 987 S 3.2/3.4L 2005-08/08
- Porsche Boxster 987 MKII 2.9L 2009-2012
- Porsche Boxster S 987 MKII 3.4L 2009-2012
- Porsche Boxster 981 2.7L 2012-16
- Porsche Boxster S 981 3.4L 2012-16
- Porsche Boxster Spyder 3.8L 2016
- Porsche 996 C2 3.4L 1997-08/01
- Porsche 996 C4 3.4L 1997-08/01
- Porsche 996 C2 3.6L 09/01-2005
- Porsche 996 C4 3.6L 09/01-2005
- Porsche 996 C4S 3.6L 09/01-2005
- Porsche 996 TURBO 2000-05
- Porsche 996 GT2 2001-05
- Porsche 996 GT3 MKI 1999-02
- Porsche 996 GT3 MKII 2003>>
- Porsche 996 GT3 RS 2003-04
- Porsche 997 Carrera 2 3.6L 2005>>
- Porsche 997 Carrera 2S 3.8L 2005>>
- Porsche 997 Carrera 4 3.6L 2005>>
- Porsche 997 Carrera 4S 3.8L 2005>>
- Porsche 997 TURBO 2007>>
- Porsche 997 GT3 2007>>
- Porsche 997 GT2 2007>>
- Porsche 997 MKII Carrera C2 3.6L 2009>>
- Porsche 997 MKII Carrera C4 3.6L 2009>>
- Porsche 997 MKII Carrera C2S 3.8L 2009>>
- Porsche 997 MKII Carrera C4S 3.8L 2009>>
- Porsche 997 MKII GT3 2010>>
- Porsche 997 MKII Turbo 2009>>
- Porsche 997 MKII GT2 RS 2011>>
- Porsche 991 Carrera C2 3.4L (350Bhp)
- Porsche 991 Carrera C2S 3.8L (400Bhp)
- Porsche 991 Carrera C4 3.4L (350Bhp)
- Porsche 991 Carrera C4S 3.8L (400Bhp)
- Porsche 991 Turbo 3.8L (520bhp)
- Porsche 991 Turbo S 3.8L (560Bhp)
- Porsche 991 R 4.0L (500 Bhp)
- Porsche 991 GT3 3.8L (475Bhp)
- Porsche 991 GT3 RS 4.0L (500Bhp)
- Porsche 991 Carrera 2 3.0L (370 Bhp)
- Porsche 991 Carrera 2S 3.0L (420 Bhp)
- Porsche 991 Carrera 4 3.0L (370 Bhp)
- Porsche 991 Carrera 4S 3.0L (420 Bhp)
- Porsche 991 Cabriolet 2 3.0L (370 Bhp)
- Porsche 991 Cabriolet 2S 3.0L (420 Bhp)
- Porsche 991 Cabriolet 4 3.0L (370 Bhp)
- Porsche 991 Cabriolet 4S 3.0L (420 Bhp)
- Porsche 991 Targa 4 3.0L (370 Bhp)
- Porsche 991 Targa 4S 3.0L (420 Bhp)
- Porsche 991 Turbo Coupe 3.8L (540 Bhp)
- Porsche 991 Turbo S Coupe 3.8L (580 Bhp)
- Porsche 991 Turbo Cabriolet 3.8L (540 Bhp)
- Porsche 991 Turbo S Cabriolet 3.8L (580 Bhp)
- Porsche Cayman 2.7L 987C 2006-08
- Porsche Cayman S 3.4L 987C 2005-08
- Porsche Cayman 2.9L 987C MKII 2009-12
- Porsche Cayman S / R 3.4L 987C MKII 2009-12
- Porsche Cayman 2.7L 981 2013-16
- Porsche Cayman S 3.4L 981 2013-16
- Porsche Cayman GT4 3.8L 2015-16
1 kit required per axle
Fits
Porsche 986 Boxster - Front and Rear
Porsche 987 Boxster and Cayman - Front and Rear
Porsche 996 - Front and Rear
Porsche 997 - Front and Rear
Porsche 981 - Front and Rear
Porsche 718 - Front and Rear
Porsche 991 - Front Only
Our Eccentric Control Arm Monoball Cartridges replace inner rubber bushings with spherical bearings, providing low friction and precisely holding camber settings.
The eccentric design allows increasing or decreasing camber, as needed.
Increasing Camber
Position the eccentric to maximize Lower Wishbone length, adding about .86 degree of negative camber on the 996/997 rear suspension, about .36 degree of negative camber on the Boxster rear suspension, and .39 degrees on the 996/997/Boxster front suspension.
Cost effective for cars that just want extra camber. For even more camber and ease of adjustment, see our GT3 type fully adjustable control arms.
Decreasing Camber
Position the eccentric to minimize Lower Wishbone length. Perfect for lowered cars that have too much negative camber and want to get back to factory camber settings to minimize tire wear on the street. Makes rear camber about .86 degrees more positive & front camber about .39 degrees positive for 996/997 while Boxsters will get about .39 degrees positive front and .36 degrees positive rear.
Made from hardened steel, plated and weather-sealed, these bearings are made to last. Fits the front or rear stock and GT3 type control arms.
Sized to fit factory original control arms. Not compatible with some aftermarket replacement control arms that use a larger non-stock size bushing.
相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号,供比较之用。
2260006
您正在查看的产品与这些编号存在交叉引用关系
- Porsche Boxster 986 2.5L 1997-99
- Porsche Boxster 986 2.7L 1999-02
- Porsche Boxster S 986 3.2L 1999-02
- Porsche Boxster 986 2.7L 2003-04
- Porsche Boxster S 986 3.2L 2003-04
- Porsche Boxster 987 2.7L 2005 -08/08
- Porsche Boxster 987 S 3.2/3.4L 2005-08/08
- Porsche Boxster 987 MKII 2.9L 2009-2012
- Porsche Boxster S 987 MKII 3.4L 2009-2012
- Porsche Boxster 718 2.0L Manual (300 Bhp)
- Porsche Boxster 718 2.0L PDK (300 Bhp)
- Porsche Boxster S 718 2.5L Manual (350 Bhp)
- Porsche Boxster S 718 2.5L PDK (350 Bhp)
- Porsche Boxster T 718 2.0L Manual (300 Bhp)
- Porsche Boxster T 718 2.0L PDK (300 Bhp)
- Porsche Boxster GTS 718 2.5L Manual (365 Bhp)
- Porsche Boxster GTS 718 2.5L PDK (365 Bhp)
- Porsche Boxster GTS 718 4.0L Manual (400 Bhp)
- Porsche Boxster GTS 718 4.0L PDK (400 Bhp)
- Porsche Boxster Spyder 718 4.0L (420 Bhp)
- Porsche Boxster 25 Years 718 4.0L Manual (400 Bhp)
- Porsche Boxster 25 Years 718 4.0L PDK (400 Bhp)
- Porsche 996 C2 3.4L 1997-08/01
- Porsche 996 C4 3.4L 1997-08/01
- Porsche 996 C2 3.6L 09/01-2005
- Porsche 996 C4 3.6L 09/01-2005
- Porsche 996 C4S 3.6L 09/01-2005
- Porsche 996 TURBO 2000-05
- Porsche 996 GT2 2001-05
- Porsche 996 GT3 MKI 1999-02
- Porsche 996 GT3 MKII 2003>>
- Porsche 996 GT3 RS 2003-04
- Porsche 997 Carrera 2 3.6L 2005>>
- Porsche 997 Carrera 2S 3.8L 2005>>
- Porsche 997 Carrera 4 3.6L 2005>>
- Porsche 997 Carrera 4S 3.8L 2005>>
- Porsche 997 TURBO 2007>>
- Porsche 997 GT3 2007>>
- Porsche 997 GT2 2007>>
- Porsche 997 MKII Carrera C2 3.6L 2009>>
- Porsche 997 MKII Carrera C4 3.6L 2009>>
- Porsche 997 MKII Carrera C2S 3.8L 2009>>
- Porsche 997 MKII Carrera C4S 3.8L 2009>>
- Porsche 997 MKII GT3 2010>>
- Porsche 997 MKII Turbo 2009>>
- Porsche 997 MKII GT2 RS 2011>>
- Porsche 991 Carrera C2 3.4L (350Bhp)
- Porsche 991 Carrera C2S 3.8L (400Bhp)
- Porsche 991 Carrera C4 3.4L (350Bhp)
- Porsche 991 Carrera C4S 3.8L (400Bhp)
- Porsche 991 Turbo 3.8L (520bhp)
- Porsche 991 Turbo S 3.8L (560Bhp)
- Porsche 991 Carrera 2 3.0L (370 Bhp)
- Porsche 991 Carrera 2S 3.0L (420 Bhp)
- Porsche 991 Carrera 4 3.0L (370 Bhp)
- Porsche 991 Carrera 4S 3.0L (420 Bhp)
- Porsche 991 Cabriolet 2 3.0L (370 Bhp)
- Porsche 991 Cabriolet 2S 3.0L (420 Bhp)
- Porsche 991 Cabriolet 4 3.0L (370 Bhp)
- Porsche 991 Cabriolet 4S 3.0L (420 Bhp)
- Porsche 991 Targa 4 3.0L (370 Bhp)
- Porsche 991 Targa 4S 3.0L (420 Bhp)
- Porsche 991 Turbo Coupe 3.8L (540 Bhp)
- Porsche 991 Turbo S Coupe 3.8L (580 Bhp)
- Porsche 991 Turbo Cabriolet 3.8L (540 Bhp)
- Porsche 991 Turbo S Cabriolet 3.8L (580 Bhp)
- Porsche Cayman 2.7L 987C 2006-08
- Porsche Cayman S 3.4L 987C 2005-08
- Porsche Cayman 2.9L 987C MKII 2009-12
- Porsche Cayman S / R 3.4L 987C MKII 2009-12
- Porsche Cayman 2.7L 981 2013-16
- Porsche Cayman S 3.4L 981 2013-16
- Porsche Cayman 718 2.0L Manual (300Bhp)
- Porsche Cayman 718 2.0L PDK (300Bhp)
- Porsche Cayman S 718 2.5L Manual (350Bhp)
- Porsche Cayman S 718 2.5L PDK (350Bhp)
- Porsche Cayman T 718 2.0L Manual (300Bhp)
- Porsche Cayman T 718 2.0L PDK (300 Bhp)
- Porsche Cayman GTS 718 2.5L Manual (365 Bhp)
- Porsche Cayman GTS 718 2.5L PDK (365 Bhp)
- Porsche Cayman GTS 718 4.0L Manual (400 Bhp)
- Porsche Cayman GTS 718 4.0L PDK (400 Bhp)
Fits cars with and without PASM
Features :
• Improved two piece 996 GT3 lower control arm design
• Stronger than cast motorsport Cup arms
• Allows proper camber adjustment
• Uses GT3 shims to adjust camber & lower control arm length (sold separately)
• High-strength steel alloy spherical bearings, completely serviceable unlike the motorsports arms
• Sealed monoball inner bearing
• Allows easy access to inner arm hardware
• Includes adjustable thrust arm bushings to adjust caster and wheelbase
• A must have for all track and race enthusiast
• Each kit includes pair of 2 arms
• Fits both front and rear axles
• Compatible with all 996/997/991/987/981 models except GT4
相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号,供比较之用。
BBILOWRCNTRL9697
您正在查看的产品与这些编号存在交叉引用关系
- Porsche Boxster 987 2.7L 2005 -08/08
- Porsche Boxster 987 S 3.2/3.4L 2005-08/08
- Porsche Boxster 987 MKII 2.9L 2009-2012
- Porsche Boxster S 987 MKII 3.4L 2009-2012
- Porsche Boxster 981 2.7L 2012-16
- Porsche Boxster S 981 3.4L 2012-16
- Porsche 996 C2 3.4L 1997-08/01
- Porsche 996 C4 3.4L 1997-08/01
- Porsche 996 C2 3.6L 09/01-2005
- Porsche 996 C4 3.6L 09/01-2005
- Porsche 996 C4S 3.6L 09/01-2005
- Porsche 996 TURBO 2000-05
- Porsche 996 GT2 2001-05
- Porsche 996 GT3 MKI 1999-02
- Porsche 996 GT3 MKII 2003>>
- Porsche 996 GT3 RS 2003-04
- Porsche 997 Carrera 2 3.6L 2005>>
- Porsche 997 Carrera 2S 3.8L 2005>>
- Porsche 997 Carrera 4 3.6L 2005>>
- Porsche 997 Carrera 4S 3.8L 2005>>
- Porsche 997 TURBO 2007>>
- Porsche 997 GT3 2007>>
- Porsche 997 GT2 2007>>
- Porsche 997 MKII Carrera C2 3.6L 2009>>
- Porsche 997 MKII Carrera C4 3.6L 2009>>
- Porsche 997 MKII Carrera C2S 3.8L 2009>>
- Porsche 997 MKII Carrera C4S 3.8L 2009>>
- Porsche 997 MKII GT3 2010>>
- Porsche 997 MKII Turbo 2009>>
- Porsche 997 MKII GT2 RS 2011>>
- Porsche 991 Carrera C2 3.4L (350Bhp)
- Porsche 991 Carrera C2S 3.8L (400Bhp)
- Porsche 991 Carrera C4 3.4L (350Bhp)
- Porsche 991 Carrera C4S 3.8L (400Bhp)
- Porsche 991 Turbo 3.8L (520bhp)
- Porsche 991 Turbo S 3.8L (560Bhp)
- Porsche 991 R 4.0L (500 Bhp)
- Porsche 991 GT3 3.8L (475Bhp)
- Porsche 991 GT3 RS 4.0L (500Bhp)
- Porsche 991 Carrera 2 3.0L (370 Bhp)
- Porsche 991 Carrera 2S 3.0L (420 Bhp)
- Porsche 991 Carrera 4 3.0L (370 Bhp)
- Porsche 991 Carrera 4S 3.0L (420 Bhp)
- Porsche 991 Cabriolet 2 3.0L (370 Bhp)
- Porsche 991 Cabriolet 2S 3.0L (420 Bhp)
- Porsche 991 Cabriolet 4 3.0L (370 Bhp)
- Porsche 991 Cabriolet 4S 3.0L (420 Bhp)
- Porsche 991 Targa 4 3.0L (370 Bhp)
- Porsche 991 Targa 4S 3.0L (420 Bhp)
- Porsche 991 Turbo Coupe 3.8L (540 Bhp)
- Porsche 991 Turbo S Coupe 3.8L (580 Bhp)
- Porsche 991 Turbo Cabriolet 3.8L (540 Bhp)
- Porsche 991 Turbo S Cabriolet 3.8L (580 Bhp)
- Porsche 991 Speedster 4.0L (510Bhp)
- Porsche 991 GT3 4.0L (500 Bhp) / GT3 RS 4.0L (520 Bhp)
- Porsche 991 GT2 RS 3.8L PDK (700 bhp)
- Porsche Cayman 2.7L 987C 2006-08
- Porsche Cayman S 3.4L 987C 2005-08
- Porsche Cayman 2.9L 987C MKII 2009-12
- Porsche Cayman S / R 3.4L 987C MKII 2009-12
- Porsche Cayman 2.7L 981 2013-16
- Porsche Cayman S 3.4L 981 2013-16
1 kit required per car
Fits
Porsche 991 2012 Onward - Rear Only
Porsche 991 Turbo 2012 Onward - Rear Only
Monoball Cartridges replace factory rubber bushings with hardened-steel spherical bearings.
Spherical bearings allow free motion on multiple axis and eliminate deflection associated with rubber, resulting in more precise holding of toe and camber.
High tolerance machined housing allow for simple press fit installation.
Correct spacers ensure proper fitment.
Weather Sealed
Monoball housing and spacers are hard anodized for protection. Our proprietary rubber seals keep the precision bearing from road contaminates for extended life of the product.
The kit includes 4 monoball bearings. two for each lower control arm. Order one kit per car
相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号,供比较之用。
2260009
您正在查看的产品与这些编号存在交叉引用关系
- Porsche 991 Carrera C2 3.4L (350Bhp)
- Porsche 991 Carrera C2S 3.8L (400Bhp)
- Porsche 991 Carrera C4 3.4L (350Bhp)
- Porsche 991 Carrera C4S 3.8L (400Bhp)
- Porsche 991 Turbo 3.8L (520bhp)
- Porsche 991 Turbo S 3.8L (560Bhp)
- Porsche 991 Carrera 2 3.0L (370 Bhp)
- Porsche 991 Carrera 2S 3.0L (420 Bhp)
- Porsche 991 Carrera 4 3.0L (370 Bhp)
- Porsche 991 Carrera 4S 3.0L (420 Bhp)
- Porsche 991 Cabriolet 2 3.0L (370 Bhp)
- Porsche 991 Cabriolet 2S 3.0L (420 Bhp)
- Porsche 991 Cabriolet 4 3.0L (370 Bhp)
- Porsche 991 Cabriolet 4S 3.0L (420 Bhp)
- Porsche 991 Targa 4 3.0L (370 Bhp)
- Porsche 991 Targa 4S 3.0L (420 Bhp)
- Porsche 991 Turbo Coupe 3.8L (540 Bhp)
- Porsche 991 Turbo S Coupe 3.8L (580 Bhp)
- Porsche 991 Turbo Cabriolet 3.8L (540 Bhp)
- Porsche 991 Turbo S Cabriolet 3.8L (580 Bhp)
1 kit required per car
Fits
Porsche 991 2012 Onward - Rear Only
Porsche 991 Turbo 2012 Onward - Rear Only
Our Eccentric Lower Wishbone Monoball Cartridges replace inner rubber bushings with spherical bearings, providing low friction and precisely holding camber settings.
The eccentric design allows increasing or decreasing rear camber, as needed.
Increasing Camber – Position the eccentric to maximize Lower Wishbone length, adding about .86 degree of negative camber on the rear suspension, .39 degrees on the front suspension. Cost effective for cars that just want extra camber. For even more camber and ease of adjustment, see our GT3 type fully adjustable control arms.
Decreasing Camber – Position the eccentric to minimize Lower Wishbone length. Perfect for lowered cars that have too much negative camber and want to get back to factory camber settings to minimize tire wear on the street. Makes rear camber about .86 degrees more positive, front camber about .39 degrees more positive.
Made from hardened steel, plated and weather-sealed, these bearings are made to last. Fits the front or rear stock and GT3 type control arms
相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号,供比较之用。
2260008
您正在查看的产品与这些编号存在交叉引用关系
- Porsche 991 Carrera C2 3.4L (350Bhp)
- Porsche 991 Carrera C2S 3.8L (400Bhp)
- Porsche 991 Carrera C4 3.4L (350Bhp)
- Porsche 991 Carrera C4S 3.8L (400Bhp)
- Porsche 991 Turbo 3.8L (520bhp)
- Porsche 991 Turbo S 3.8L (560Bhp)
- Porsche 991 Carrera 2 3.0L (370 Bhp)
- Porsche 991 Carrera 2S 3.0L (420 Bhp)
- Porsche 991 Carrera 4 3.0L (370 Bhp)
- Porsche 991 Carrera 4S 3.0L (420 Bhp)
- Porsche 991 Cabriolet 2 3.0L (370 Bhp)
- Porsche 991 Cabriolet 2S 3.0L (420 Bhp)
- Porsche 991 Cabriolet 4 3.0L (370 Bhp)
- Porsche 991 Cabriolet 4S 3.0L (420 Bhp)
- Porsche 991 Targa 4 3.0L (370 Bhp)
- Porsche 991 Targa 4S 3.0L (420 Bhp)
- Porsche 991 Turbo Coupe 3.8L (540 Bhp)
- Porsche 991 Turbo S Coupe 3.8L (580 Bhp)
- Porsche 991 Turbo Cabriolet 3.8L (540 Bhp)
- Porsche 991 Turbo S Cabriolet 3.8L (580 Bhp)
Fits
991.1 and 991.2 Carrera and Carrera S
991.1 and 991.2 Carrera 4 and Carrera 4S
991.1 and 991.2 GTS
991.1 and 991.2 turbo
Product Description:
The BBi Autosport "Dogbone" Rear arm set upgrades the factory control arms with machined and anodized units designed to house spherical bearings.
The full set replaces the arms with rubber bushings and bring back control, stability and predictability in the suspension - much like the RS models.
These are fully serviceable parts.
相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号,供比较之用。
BBIDOGBONE991
您正在查看的产品与这些编号存在交叉引用关系
- Porsche 991 Carrera C2 3.4L (350Bhp)
- Porsche 991 Carrera C2S 3.8L (400Bhp)
- Porsche 991 Carrera C4 3.4L (350Bhp)
- Porsche 991 Carrera C4S 3.8L (400Bhp)
- Porsche 991 Turbo 3.8L (520bhp)
- Porsche 991 Turbo S 3.8L (560Bhp)
- Porsche 991 Carrera 2 3.0L (370 Bhp)
- Porsche 991 Carrera 2S 3.0L (420 Bhp)
- Porsche 991 Carrera 4 3.0L (370 Bhp)
- Porsche 991 Carrera 4S 3.0L (420 Bhp)
- Porsche 991 Cabriolet 2 3.0L (370 Bhp)
- Porsche 991 Cabriolet 2S 3.0L (420 Bhp)
- Porsche 991 Cabriolet 4 3.0L (370 Bhp)
- Porsche 991 Cabriolet 4S 3.0L (420 Bhp)
- Porsche 991 Targa 4 3.0L (370 Bhp)
- Porsche 991 Targa 4S 3.0L (420 Bhp)
- Porsche 991 Turbo Coupe 3.8L (540 Bhp)
- Porsche 991 Turbo S Coupe 3.8L (580 Bhp)
- Porsche 991 Turbo Cabriolet 3.8L (540 Bhp)
- Porsche 991 Turbo S Cabriolet 3.8L (580 Bhp)
1 kit required per car
Fits
Porsche 991 2012 Onward - Rear Only
Porsche 991 Turbo 2012 Onward - Rear Only
Monoball Cartridges replace factory rear track rod bushings with hardened-steel spherical bearings. Spherical bearings allow free motion on multiple axis and eliminate deflection associated with rubber, resulting in more precise holding of toe and camber.
High tolerance machined housing allow for simple press fit installation. Correct spacers ensure proper fitment.
Eccentric bearings are made from hardened steel, plated and weather-sealed to keep road contaminates out.
These bearings are made to last.
The kit includes 4 monoball bearings. 2 bearings per arm, for both track rods.
Order one kit per car
相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号,供比较之用。
2260015
您正在查看的产品与这些编号存在交叉引用关系
- Porsche 991 Carrera C2 3.4L (350Bhp)
- Porsche 991 Carrera C2S 3.8L (400Bhp)
- Porsche 991 Carrera C4 3.4L (350Bhp)
- Porsche 991 Carrera C4S 3.8L (400Bhp)
- Porsche 991 Turbo 3.8L (520bhp)
- Porsche 991 Turbo S 3.8L (560Bhp)
- Porsche 991 Carrera 2 3.0L (370 Bhp)
- Porsche 991 Carrera 2S 3.0L (420 Bhp)
- Porsche 991 Carrera 4 3.0L (370 Bhp)
- Porsche 991 Carrera 4S 3.0L (420 Bhp)
- Porsche 991 Cabriolet 2 3.0L (370 Bhp)
- Porsche 991 Cabriolet 2S 3.0L (420 Bhp)
- Porsche 991 Cabriolet 4 3.0L (370 Bhp)
- Porsche 991 Cabriolet 4S 3.0L (420 Bhp)
- Porsche 991 Targa 4 3.0L (370 Bhp)
- Porsche 991 Targa 4S 3.0L (420 Bhp)
- Porsche 991 Turbo Coupe 3.8L (540 Bhp)
- Porsche 991 Turbo S Coupe 3.8L (580 Bhp)
- Porsche 991 Turbo Cabriolet 3.8L (540 Bhp)
- Porsche 991 Turbo S Cabriolet 3.8L (580 Bhp)
1 kit required per car
Fits
Porsche 991 2012 Onward - Rear Only
Porsche 991 Turbo 2012 Onward - Rear Only
This monoball cartridge kit replace the inner and outer track rod bushings.
The inner Eccentric bearings provide increased range of toe adjustment. This is to compensate for increased camber or lowered car that cannot be brought into toe range. The outer concentric bearing replaces the rubber bushing and eliminates deflection due to rubber compression.
Increasing Camber – Position the eccentric to maximize Lower Wishbone length, adding about .86 degree of negative camber on the rear suspension, .39 degrees on the front suspension. Cost effective for cars that just want extra camber. For even more camber and ease of adjustment, see our GT3 type fully adjustable control arms.
Decreasing Camber – Position the eccentric to minimize Lower Wishbone length. Perfect for lowered cars that have too much negative camber and want to get back to factory camber settings to minimize tire wear on the street. Makes rear camber about .86 degrees more positive, front camber about .39 degrees more positive.
Eccentric bearings are made from hardened steel, plated and weather-sealed to keep road contaminates out. These bearings are made to last.
相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号,供比较之用。
2260013
您正在查看的产品与这些编号存在交叉引用关系
- Porsche 991 Carrera C2 3.4L (350Bhp)
- Porsche 991 Carrera C2S 3.8L (400Bhp)
- Porsche 991 Carrera C4 3.4L (350Bhp)
- Porsche 991 Carrera C4S 3.8L (400Bhp)
- Porsche 991 Turbo 3.8L (520bhp)
- Porsche 991 Turbo S 3.8L (560Bhp)
- Porsche 991 Carrera 2 3.0L (370 Bhp)
- Porsche 991 Carrera 2S 3.0L (420 Bhp)
- Porsche 991 Carrera 4 3.0L (370 Bhp)
- Porsche 991 Carrera 4S 3.0L (420 Bhp)
- Porsche 991 Cabriolet 2 3.0L (370 Bhp)
- Porsche 991 Cabriolet 2S 3.0L (420 Bhp)
- Porsche 991 Cabriolet 4 3.0L (370 Bhp)
- Porsche 991 Cabriolet 4S 3.0L (420 Bhp)
- Porsche 991 Targa 4 3.0L (370 Bhp)
- Porsche 991 Targa 4S 3.0L (420 Bhp)
- Porsche 991 Turbo Coupe 3.8L (540 Bhp)
- Porsche 991 Turbo S Coupe 3.8L (580 Bhp)
- Porsche 991 Turbo Cabriolet 3.8L (540 Bhp)
- Porsche 991 Turbo S Cabriolet 3.8L (580 Bhp)
1 x tool required per application
Fits
Porsche 991 - Rear
Porsche 991 Turbo - Rear
Simplify the installation process of Monoball products and replacement bushings.
Our two piece cup and piston tools allow for simple bushing extraction and insertion without removal of the wheel carriers or control arms. No need to use a shop press. The tools are designed to precisely fit the bushing circumference, preventing accidental damage to the bushing and ensuring proper installation.
We have tools for the LCA central bushings, the rear upright LCA bushings, and the rear upright shock mount bushings.
相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号,供比较之用。
226001
您正在查看的产品与这些编号存在交叉引用关系
- Porsche 991 Carrera C2 3.4L (350Bhp)
- Porsche 991 Carrera C2S 3.8L (400Bhp)
- Porsche 991 Carrera C4 3.4L (350Bhp)
- Porsche 991 Carrera C4S 3.8L (400Bhp)
- Porsche 991 Turbo 3.8L (520bhp)
- Porsche 991 Turbo S 3.8L (560Bhp)
- Porsche 991 R 4.0L (500 Bhp)
- Porsche 991 GT3 3.8L (475Bhp)
- Porsche 991 GT3 RS 4.0L (500Bhp)
- Porsche 991 Carrera 2 3.0L (370 Bhp)
- Porsche 991 Carrera 2S 3.0L (420 Bhp)
- Porsche 991 Carrera 4 3.0L (370 Bhp)
- Porsche 991 Carrera 4S 3.0L (420 Bhp)
- Porsche 991 Cabriolet 2 3.0L (370 Bhp)
- Porsche 991 Cabriolet 2S 3.0L (420 Bhp)
- Porsche 991 Cabriolet 4 3.0L (370 Bhp)
- Porsche 991 Cabriolet 4S 3.0L (420 Bhp)
- Porsche 991 Targa 4 3.0L (370 Bhp)
- Porsche 991 Targa 4S 3.0L (420 Bhp)
- Porsche 991 Turbo Coupe 3.8L (540 Bhp)
- Porsche 991 Turbo S Coupe 3.8L (580 Bhp)
- Porsche 991 Turbo Cabriolet 3.8L (540 Bhp)
- Porsche 991 Turbo S Cabriolet 3.8L (580 Bhp)
Price is EACH
Fits
Porsche 991 2012 Onward - Rear Only
Porsche 991 Turbo 2012 Onward - Rear Only
相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号,供比较之用。
99133111212
您正在查看的产品与这些编号存在交叉引用关系
- Porsche 991 Carrera C2 3.4L (350Bhp)
- Porsche 991 Carrera C2S 3.8L (400Bhp)
- Porsche 991 Carrera C4 3.4L (350Bhp)
- Porsche 991 Carrera C4S 3.8L (400Bhp)
- Porsche 991 Turbo 3.8L (520bhp)
- Porsche 991 Turbo S 3.8L (560Bhp)
- Porsche 991 Carrera 2 3.0L (370 Bhp)
- Porsche 991 Carrera 2S 3.0L (420 Bhp)
- Porsche 991 Carrera 4 3.0L (370 Bhp)
- Porsche 991 Carrera 4S 3.0L (420 Bhp)
- Porsche 991 Cabriolet 2 3.0L (370 Bhp)
- Porsche 991 Cabriolet 2S 3.0L (420 Bhp)
- Porsche 991 Cabriolet 4 3.0L (370 Bhp)
- Porsche 991 Cabriolet 4S 3.0L (420 Bhp)
- Porsche 991 Targa 4 3.0L (370 Bhp)
- Porsche 991 Targa 4S 3.0L (420 Bhp)
- Porsche 991 Turbo Coupe 3.8L (540 Bhp)
- Porsche 991 Turbo S Coupe 3.8L (580 Bhp)
- Porsche 991 Turbo Cabriolet 3.8L (540 Bhp)
- Porsche 991 Turbo S Cabriolet 3.8L (580 Bhp)
Price is EACH
Fits
Porsche 991 2012 Onward - Rear Only
Porsche 991 Turbo 2012 Onward - Rear Only
相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号,供比较之用。
99133111212
您正在查看的产品与这些编号存在交叉引用关系
- Porsche 991 Carrera C2 3.4L (350Bhp)
- Porsche 991 Carrera C2S 3.8L (400Bhp)
- Porsche 991 Carrera C4 3.4L (350Bhp)
- Porsche 991 Carrera C4S 3.8L (400Bhp)
- Porsche 991 Turbo 3.8L (520bhp)
- Porsche 991 Turbo S 3.8L (560Bhp)
- Porsche 991 Carrera 2 3.0L (370 Bhp)
- Porsche 991 Carrera 2S 3.0L (420 Bhp)
- Porsche 991 Carrera 4 3.0L (370 Bhp)
- Porsche 991 Carrera 4S 3.0L (420 Bhp)
- Porsche 991 Cabriolet 2 3.0L (370 Bhp)
- Porsche 991 Cabriolet 2S 3.0L (420 Bhp)
- Porsche 991 Cabriolet 4 3.0L (370 Bhp)
- Porsche 991 Cabriolet 4S 3.0L (420 Bhp)
- Porsche 991 Targa 4 3.0L (370 Bhp)
- Porsche 991 Targa 4S 3.0L (420 Bhp)
- Porsche 991 Turbo Coupe 3.8L (540 Bhp)
- Porsche 991 Turbo S Coupe 3.8L (580 Bhp)
- Porsche 991 Turbo Cabriolet 3.8L (540 Bhp)
- Porsche 991 Turbo S Cabriolet 3.8L (580 Bhp)
1 kit required per car
Fits
Porsche 991 2012 Onward - Rear Only
Porsche 991 Turbo 2012 Onward - Rear Only
Monoball Cartridges replace factory rear wheel carrier bushings with hardened-steel spherical bearings. Spherical bearings allow free motion on multiple axis and eliminate deflection associated with rubber, resulting in more precise holding of toe and camber.
High tolerance machined housing allow for simple press fit installation. Correct spacers ensure proper fitment.
Weather Sealed
Monoball housing and spacers are hard anodized for protection. Our proprietary rubber seals keep the precision bearing from road contaminates for extended life of the product.
The kit includes two monoball bearings… one for each rear wheel carrier
相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号,供比较之用。
2260011
您正在查看的产品与这些编号存在交叉引用关系
- Porsche 991 Carrera C2 3.4L (350Bhp)
- Porsche 991 Carrera C2S 3.8L (400Bhp)
- Porsche 991 Carrera C4 3.4L (350Bhp)
- Porsche 991 Carrera C4S 3.8L (400Bhp)
- Porsche 991 Turbo 3.8L (520bhp)
- Porsche 991 Turbo S 3.8L (560Bhp)
- Porsche 991 Carrera 2 3.0L (370 Bhp)
- Porsche 991 Carrera 2S 3.0L (420 Bhp)
- Porsche 991 Carrera 4 3.0L (370 Bhp)
- Porsche 991 Carrera 4S 3.0L (420 Bhp)
- Porsche 991 Cabriolet 2 3.0L (370 Bhp)
- Porsche 991 Cabriolet 2S 3.0L (420 Bhp)
- Porsche 991 Cabriolet 4 3.0L (370 Bhp)
- Porsche 991 Cabriolet 4S 3.0L (420 Bhp)
- Porsche 991 Targa 4 3.0L (370 Bhp)
- Porsche 991 Targa 4S 3.0L (420 Bhp)
- Porsche 991 Turbo Coupe 3.8L (540 Bhp)
- Porsche 991 Turbo S Coupe 3.8L (580 Bhp)
- Porsche 991 Turbo Cabriolet 3.8L (540 Bhp)
- Porsche 991 Turbo S Cabriolet 3.8L (580 Bhp)
SET OF 4. FRONT AXLE ONLY
The RSS Adjustable Thrust Arm Bushing Kit will improve handling and response in 987. 997, 981, GT4, 991 GT3 variants, suspension systems and allows for additional caster adjustments. Eliminates unwanted caster changes in both front and rear suspension under acceleration and deceleration.
AVAILABLE FOR ALL PORSCHE® 987,981, GT4, 997, 991 and 991 GT3, and 991 TURBO
NOT FOR 997 GT3/GT2
相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号,供比较之用。
360
您正在查看的产品与这些编号存在交叉引用关系
- Porsche Boxster 987 2.7L 2005 -08/08
- Porsche Boxster 987 S 3.2/3.4L 2005-08/08
- Porsche Boxster 987 MKII 2.9L 2009-2012
- Porsche Boxster S 987 MKII 3.4L 2009-2012
- Porsche Boxster 981 2.7L 2012-16
- Porsche Boxster S 981 3.4L 2012-16
- Porsche 997 Carrera 2 3.6L 2005>>
- Porsche 997 Carrera 2S 3.8L 2005>>
- Porsche 997 Carrera 4 3.6L 2005>>
- Porsche 997 Carrera 4S 3.8L 2005>>
- Porsche 997 TURBO 2007>>
- Porsche 997 MKII Carrera C2 3.6L 2009>>
- Porsche 997 MKII Carrera C4 3.6L 2009>>
- Porsche 997 MKII Carrera C2S 3.8L 2009>>
- Porsche 997 MKII Carrera C4S 3.8L 2009>>
- Porsche 997 MKII Turbo 2009>>
- Porsche 991 Carrera C2 3.4L (350Bhp)
- Porsche 991 Carrera C2S 3.8L (400Bhp)
- Porsche 991 Carrera C4 3.4L (350Bhp)
- Porsche 991 Carrera C4S 3.8L (400Bhp)
- Porsche 991 Turbo 3.8L (520bhp)
- Porsche 991 Turbo S 3.8L (560Bhp)
- Porsche 991 R 4.0L (500 Bhp)
- Porsche 991 GT3 3.8L (475Bhp)
- Porsche 991 GT3 RS 4.0L (500Bhp)
- Porsche 991 Carrera 2 3.0L (370 Bhp)
- Porsche 991 Carrera 2S 3.0L (420 Bhp)
- Porsche 991 Carrera 4 3.0L (370 Bhp)
- Porsche 991 Carrera 4S 3.0L (420 Bhp)
- Porsche 991 Cabriolet 2 3.0L (370 Bhp)
- Porsche 991 Cabriolet 2S 3.0L (420 Bhp)
- Porsche 991 Cabriolet 4 3.0L (370 Bhp)
- Porsche 991 Cabriolet 4S 3.0L (420 Bhp)
- Porsche 991 Targa 4 3.0L (370 Bhp)
- Porsche 991 Targa 4S 3.0L (420 Bhp)
- Porsche 991 Turbo Coupe 3.8L (540 Bhp)
- Porsche 991 Turbo S Coupe 3.8L (580 Bhp)
- Porsche 991 Turbo Cabriolet 3.8L (540 Bhp)
- Porsche 991 Turbo S Cabriolet 3.8L (580 Bhp)
- Porsche 991 GT3 4.0L (500 Bhp) / GT3 RS 4.0L (520 Bhp)
- Porsche Cayman 2.7L 987C 2006-08
- Porsche Cayman S 3.4L 987C 2005-08
- Porsche Cayman 2.9L 987C MKII 2009-12
- Porsche Cayman S / R 3.4L 987C MKII 2009-12
- Porsche Cayman 2.7L 981 2013-16
- Porsche Cayman S 3.4L 981 2013-16
- Porsche Cayman GT4 3.8L 2015-16
Includes:
1 x Tapered Stud,
1 x Upper Lock Nut,
1 x Lower Lock Nut and
4 x Roll Center Spacers/Washers.
1 Kit Per RSS Lower Control Arm (Fits: Part #s: 356, 357, 361, 372, 373, 374 and 366).
USER NOTE: A new 380 Kit should be installed once ball joint pin has been removed from hub. See Lower Control Arm Notes.
相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号,供比较之用。
380
您正在查看的产品与这些编号存在交叉引用关系
- Porsche Boxster 986 2.5L 1997-99
- Porsche Boxster 986 2.7L 1999-02
- Porsche Boxster S 986 3.2L 1999-02
- Porsche Boxster 986 2.7L 2003-04
- Porsche Boxster S 986 3.2L 2003-04
- Porsche Boxster 987 2.7L 2005 -08/08
- Porsche Boxster 987 S 3.2/3.4L 2005-08/08
- Porsche Boxster 987 MKII 2.9L 2009-2012
- Porsche Boxster S 987 MKII 3.4L 2009-2012
- Porsche Boxster 981 2.7L 2012-16
- Porsche Boxster S 981 3.4L 2012-16
- Porsche 996 C2 3.4L 1997-08/01
- Porsche 996 C4 3.4L 1997-08/01
- Porsche 996 C2 3.6L 09/01-2005
- Porsche 996 C4 3.6L 09/01-2005
- Porsche 996 C4S 3.6L 09/01-2005
- Porsche 996 TURBO 2000-05
- Porsche 996 GT2 2001-05
- Porsche 996 GT3 MKI 1999-02
- Porsche 996 GT3 MKII 2003>>
- Porsche 996 GT3 RS 2003-04
- Porsche 997 Carrera 2 3.6L 2005>>
- Porsche 997 Carrera 2S 3.8L 2005>>
- Porsche 997 Carrera 4 3.6L 2005>>
- Porsche 997 Carrera 4S 3.8L 2005>>
- Porsche 997 TURBO 2007>>
- Porsche 997 GT3 2007>>
- Porsche 997 GT2 2007>>
- Porsche 997 MKII Carrera C2 3.6L 2009>>
- Porsche 997 MKII Carrera C4 3.6L 2009>>
- Porsche 997 MKII Carrera C2S 3.8L 2009>>
- Porsche 997 MKII Carrera C4S 3.8L 2009>>
- Porsche 997 MKII GT3 2010>>
- Porsche 997 MKII Turbo 2009>>
- Porsche 991 Carrera C2 3.4L (350Bhp)
- Porsche 991 Carrera C2S 3.8L (400Bhp)
- Porsche 991 Carrera C4 3.4L (350Bhp)
- Porsche 991 Carrera C4S 3.8L (400Bhp)
- Porsche 991 Turbo 3.8L (520bhp)
- Porsche 991 Turbo S 3.8L (560Bhp)
- Porsche 991 Carrera 2 3.0L (370 Bhp)
- Porsche 991 Carrera 2S 3.0L (420 Bhp)
- Porsche 991 Carrera 4 3.0L (370 Bhp)
- Porsche 991 Carrera 4S 3.0L (420 Bhp)
- Porsche 991 Cabriolet 2 3.0L (370 Bhp)
- Porsche 991 Cabriolet 2S 3.0L (420 Bhp)
- Porsche 991 Cabriolet 4 3.0L (370 Bhp)
- Porsche 991 Cabriolet 4S 3.0L (420 Bhp)
- Porsche 991 Targa 4 3.0L (370 Bhp)
- Porsche 991 Targa 4S 3.0L (420 Bhp)
- Porsche 991 Turbo Coupe 3.8L (540 Bhp)
- Porsche 991 Turbo S Coupe 3.8L (580 Bhp)
- Porsche 991 Turbo Cabriolet 3.8L (540 Bhp)
- Porsche 991 Turbo S Cabriolet 3.8L (580 Bhp)
- Porsche Cayman 2.7L 987C 2006-08
- Porsche Cayman S 3.4L 987C 2005-08
- Porsche Cayman 2.9L 987C MKII 2009-12
- Porsche Cayman S / R 3.4L 987C MKII 2009-12
- Porsche Cayman 2.7L 981 2013-16
- Porsche Cayman S 3.4L 981 2013-16
- Porsche Cayman GT4 3.8L 2015-16
RSS Tarmac Series Motorsport Lower Control Arms are specifically engineered for use on lowered vehicles that have reduced travel struts/dampers such as PASM or M030 option. Alternatively if the car is equipped with high quality aftermarket or motorsport coilover kits ie Bilstein PSS10, KW V3 or Ohlins etc.
The Lower Control Arms are NOT COMPATIBLE with "Base Model Suspension" (long travel struts/dampers) or "Base Model struts/dampers with lowering springs."
Caution: Do not install on vehicles with Base Model struts/dampers as it may result in an unsafe driving condition with possibility of suspension bind when struts/dampers are fully extended or in full drop.
Fits:
FOR REAR AXLE PORSCHE 986, 996, 997, 987, 981/982/718
Includes:
- Adjustable/Non-Hydraulic Replacement Thrust Arm Bushings,
- 1mm/2mm/3mm/7mm Shims,
- Spherical Monoball Ends.
*** Note: 981 and 991 Models may require additional Front Litronic or Torque Vector Sensor Brackets.
RSS Tarmac Series Motorsport Lower Control Arms are specifically engineered for use on lowered vehicles that have reduced travel struts/dampers If you need assistance in identifying your suspension type please contact us. For specific fitment information refer to the "Chassis Fitment Guide and Lower Control Arm Fitment Notes" (See Images Below).
The RSS Tarmac Series – Motorsports Control Arms are designed for the Porsche driver who demands the absolute maximum in precision handling, feedback and control from their chassis. This system has been specially engineered to provide unmatched performance, quality, strength and serviceability. RSS Tarmac Series Control Arms address the performance related shortcomings of the OEM rubber mounted suspension components which were designed to reduce road noise and vibration for everyday street use. The use of rubber injected moldings in mounting components such as the control arms, thrust arms, upper links and toe arms is a compromise in regards to maximum suspension performance. The soft rubber deflects under suspension load which in turn causes unwanted movement (deflection) between the suspension and chassis. Data also shows that temporary changes in spring rates can occur as well. These movements and changes result in unnecessary corrections and inputs from the driver.
FEATURES & BENEFITS:
• Replaceable Sub-Assemblies: For the extreme, repetitive track day enthusiast or racer, our high strength
steel alloy spherical bearings (with a friction reducing, longevity increasing Teflon liner) outer and inner arm sub-assemblies can be replaced
unlike the motorsports arms, in which case a new set of arms will need to be purchased if the
spherical bearings are worn out.
• Adjustable Suspension Geometry: Adjust dynamic camber values and roll center heights with our
unique zinc plated steel bushings.
• Solid Monoball Control Arm Ends: Offers better handling and a more responsive suspension over the
factory one-piece rubber injected control arm by eliminating bushing deflection (also uses the same
high strength steel alloy spherical bearing found in our control arm monoball kit).
• 6061 Aerospace Grade Billet Aluminum Construction: Allows for a more uniform molecular structure
at every point of the arm over the cast components providing a more durable and inherently
stronger part. Manufacturing from billet aluminum rather than casting results in fewer impurities in
the metal.
• Anodized Aluminum Surfaces and Zinc Plated Steel Parts: Allows for better corrosion resistance
against the elements.
AVAILABLE FOR MOST PORSCHE 996, 986, 981, 982, 987 & 997 MODELS INCLUDING TURBO, GT2, GT2RS, GT3 & GT3RS.
RSS TARMAC SERIES Motorsports Suspension Kits have been winning championships and races in various forms of motorsport (Road Racing to Rally) around the world. RSS is the suspension of choice of professional race teams, tuners, track day junkies, and driving enthusiasts around the world.
- 2015 PIRELLI WORLD CHALLENGE TC CHAMPIONS
- 2014 FIA SPANISH RALLY TARMAC CHAMPIONS
- 2013 ROLEX GRAND-AM GX CHAMPIONS
RSS High Performance Tarmac Series Suspension Components are designed, engineered and manufactured on location here in the USA.
相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号,供比较之用。
374
您正在查看的产品与这些编号存在交叉引用关系
- Porsche Boxster 986 2.5L 1997-99
- Porsche Boxster 986 2.7L 1999-02
- Porsche Boxster S 986 3.2L 1999-02
- Porsche Boxster 986 2.7L 2003-04
- Porsche Boxster S 986 3.2L 2003-04
- Porsche Boxster 987 2.7L 2005 -08/08
- Porsche Boxster 987 S 3.2/3.4L 2005-08/08
- Porsche Boxster 987 MKII 2.9L 2009-2012
- Porsche Boxster S 987 MKII 3.4L 2009-2012
- Porsche Boxster 981 2.7L 2012-16
- Porsche Boxster S 981 3.4L 2012-16
- Porsche Boxster 718 2.0L Manual (300 Bhp)
- Porsche Boxster 718 2.0L PDK (300 Bhp)
- Porsche Boxster S 718 2.5L Manual (350 Bhp)
- Porsche Boxster S 718 2.5L PDK (350 Bhp)
- Porsche 996 C2 3.4L 1997-08/01
- Porsche 996 C4 3.4L 1997-08/01
- Porsche 996 C2 3.6L 09/01-2005
- Porsche 996 C4 3.6L 09/01-2005
- Porsche 996 C4S 3.6L 09/01-2005
- Porsche 996 TURBO 2000-05
- Porsche 996 GT2 2001-05
- Porsche 996 GT3 MKI 1999-02
- Porsche 996 GT3 MKII 2003>>
- Porsche 996 GT3 RS 2003-04
- Porsche 997 Carrera 2 3.6L 2005>>
- Porsche 997 Carrera 2S 3.8L 2005>>
- Porsche 997 Carrera 4 3.6L 2005>>
- Porsche 997 Carrera 4S 3.8L 2005>>
- Porsche 997 TURBO 2007>>
- Porsche 997 GT3 2007>>
- Porsche 997 GT2 2007>>
- Porsche 997 MKII Carrera C2 3.6L 2009>>
- Porsche 997 MKII Carrera C4 3.6L 2009>>
- Porsche 997 MKII Carrera C2S 3.8L 2009>>
- Porsche 997 MKII Carrera C4S 3.8L 2009>>
- Porsche 997 MKII GT3 2010>>
- Porsche 997 MKII Turbo 2009>>
- Porsche 997 MKII GT2 RS 2011>>
- Porsche 991 Carrera C2 3.4L (350Bhp)
- Porsche 991 Carrera C2S 3.8L (400Bhp)
- Porsche 991 Carrera C4 3.4L (350Bhp)
- Porsche 991 Carrera C4S 3.8L (400Bhp)
- Porsche 991 Turbo 3.8L (520bhp)
- Porsche 991 Turbo S 3.8L (560Bhp)
- Porsche 991 R 4.0L (500 Bhp)
- Porsche 991 GT3 3.8L (475Bhp)
- Porsche 991 GT3 RS 4.0L (500Bhp)
- Porsche 991 Carrera 2 3.0L (370 Bhp)
- Porsche 991 Carrera 2S 3.0L (420 Bhp)
- Porsche 991 Carrera 4 3.0L (370 Bhp)
- Porsche 991 Carrera 4S 3.0L (420 Bhp)
- Porsche 991 Cabriolet 2 3.0L (370 Bhp)
- Porsche 991 Cabriolet 2S 3.0L (420 Bhp)
- Porsche 991 Cabriolet 4 3.0L (370 Bhp)
- Porsche 991 Cabriolet 4S 3.0L (420 Bhp)
- Porsche 991 Targa 4 3.0L (370 Bhp)
- Porsche 991 Targa 4S 3.0L (420 Bhp)
- Porsche 991 Turbo Coupe 3.8L (540 Bhp)
- Porsche 991 Turbo S Coupe 3.8L (580 Bhp)
- Porsche 991 Turbo Cabriolet 3.8L (540 Bhp)
- Porsche 991 Turbo S Cabriolet 3.8L (580 Bhp)
- Porsche 991 GT3 4.0L (500 Bhp) / GT3 RS 4.0L (520 Bhp)
- Porsche 991 GT2 RS 3.8L PDK (700 bhp)
- Porsche Cayman 2.7L 987C 2006-08
- Porsche Cayman S 3.4L 987C 2005-08
- Porsche Cayman 2.9L 987C MKII 2009-12
- Porsche Cayman S / R 3.4L 987C MKII 2009-12
- Porsche Cayman 2.7L 981 2013-16
- Porsche Cayman S 3.4L 981 2013-16
- Porsche Cayman GT4 3.8L 2015-16
- Porsche Cayman 718 2.0L Manual (300Bhp)
- Porsche Cayman 718 2.0L PDK (300Bhp)
- Porsche Cayman S 718 2.5L Manual (350Bhp)
- Porsche Cayman S 718 2.5L PDK (350Bhp)
SET OF 4. REAR AXLE ONLY
Brand:
The RSS Non-Adjustable Thrust Arm Bushing Kit will improve handling and response in suspension systems. Eliminates unwanted caster changes in both front and rear suspension under acceleration and deceleration.
AVAILABLE FOR ALL PORSCHE® 986, 987, 996, 997, 981 MODELS INCLUDING TURBO & GT3 FOR NON-HYDRAULIC APPLICATIONS ONLY FOR HYDRAULIC APPLICATIONS.
相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号,供比较之用。
334
您正在查看的产品与这些编号存在交叉引用关系
- Porsche Boxster 986 2.5L 1997-99
- Porsche Boxster 986 2.7L 1999-02
- Porsche Boxster S 986 3.2L 1999-02
- Porsche Boxster 986 2.7L 2003-04
- Porsche Boxster S 986 3.2L 2003-04
- Porsche Boxster 987 2.7L 2005 -08/08
- Porsche Boxster 987 S 3.2/3.4L 2005-08/08
- Porsche Boxster 987 MKII 2.9L 2009-2012
- Porsche Boxster S 987 MKII 3.4L 2009-2012
- Porsche Boxster 981 2.7L 2012-16
- Porsche Boxster S 981 3.4L 2012-16
- Porsche Boxster 718 2.0L Manual (300 Bhp)
- Porsche Boxster 718 2.0L PDK (300 Bhp)
- Porsche Boxster S 718 2.5L Manual (350 Bhp)
- Porsche Boxster S 718 2.5L PDK (350 Bhp)
- Porsche 996 C2 3.4L 1997-08/01
- Porsche 996 C4 3.4L 1997-08/01
- Porsche 996 C2 3.6L 09/01-2005
- Porsche 996 C4 3.6L 09/01-2005
- Porsche 996 C4S 3.6L 09/01-2005
- Porsche 996 TURBO 2000-05
- Porsche 996 GT2 2001-05
- Porsche 996 GT3 MKI 1999-02
- Porsche 996 GT3 MKII 2003>>
- Porsche 996 GT3 RS 2003-04
- Porsche 997 Carrera 2 3.6L 2005>>
- Porsche 997 Carrera 2S 3.8L 2005>>
- Porsche 997 Carrera 4 3.6L 2005>>
- Porsche 997 Carrera 4S 3.8L 2005>>
- Porsche 997 TURBO 2007>>
- Porsche 997 GT3 2007>>
- Porsche 997 GT2 2007>>
- Porsche 997 MKII Carrera C2 3.6L 2009>>
- Porsche 997 MKII Carrera C4 3.6L 2009>>
- Porsche 997 MKII Carrera C2S 3.8L 2009>>
- Porsche 997 MKII Carrera C4S 3.8L 2009>>
- Porsche 997 MKII GT3 2010>>
- Porsche 997 MKII Turbo 2009>>
- Porsche 997 MKII GT2 RS 2011>>
- Porsche 991 Carrera C2 3.4L (350Bhp)
- Porsche 991 Carrera C2S 3.8L (400Bhp)
- Porsche 991 Carrera C4 3.4L (350Bhp)
- Porsche 991 Carrera C4S 3.8L (400Bhp)
- Porsche 991 Turbo 3.8L (520bhp)
- Porsche 991 Turbo S 3.8L (560Bhp)
- Porsche 991 R 4.0L (500 Bhp)
- Porsche 991 GT3 3.8L (475Bhp)
- Porsche 991 GT3 RS 4.0L (500Bhp)
- Porsche 991 Carrera 2 3.0L (370 Bhp)
- Porsche 991 Carrera 2S 3.0L (420 Bhp)
- Porsche 991 Carrera 4 3.0L (370 Bhp)
- Porsche 991 Carrera 4S 3.0L (420 Bhp)
- Porsche 991 Cabriolet 2 3.0L (370 Bhp)
- Porsche 991 Cabriolet 2S 3.0L (420 Bhp)
- Porsche 991 Cabriolet 4 3.0L (370 Bhp)
- Porsche 991 Cabriolet 4S 3.0L (420 Bhp)
- Porsche 991 Targa 4 3.0L (370 Bhp)
- Porsche 991 Targa 4S 3.0L (420 Bhp)
- Porsche 991 Turbo Coupe 3.8L (540 Bhp)
- Porsche 991 Turbo S Coupe 3.8L (580 Bhp)
- Porsche 991 Turbo Cabriolet 3.8L (540 Bhp)
- Porsche 991 Turbo S Cabriolet 3.8L (580 Bhp)
- Porsche 991 GT3 4.0L (500 Bhp) / GT3 RS 4.0L (520 Bhp)
- Porsche 991 GT2 RS 3.8L PDK (700 bhp)
- Porsche Cayman 2.7L 987C 2006-08
- Porsche Cayman S 3.4L 987C 2005-08
- Porsche Cayman 2.9L 987C MKII 2009-12
- Porsche Cayman S / R 3.4L 987C MKII 2009-12
- Porsche Cayman 2.7L 981 2013-16
- Porsche Cayman S 3.4L 981 2013-16
- Porsche Cayman GT4 3.8L 2015-16
- Porsche Cayman 718 2.0L Manual (300Bhp)
- Porsche Cayman 718 2.0L PDK (300Bhp)
- Porsche Cayman S 718 2.5L Manual (350Bhp)
- Porsche Cayman S 718 2.5L PDK (350Bhp)
2 件套
适合:
保时捷 996 C2、C4、C4S、Turbo、GT2、GT3
保时捷 997 C2、C2S、C4、C4S、Turbo、GT2、GT3
保时捷 986 Boxster / Boxster S
保时捷 987 Boxster / Boxster S
保时捷 987 Cayman / Cayman S
保时捷 981 Boxster / Boxster S
保时捷 981 Cayman / Cayman S / Cayman GT4
保时捷 991 C2、C2S、C4、C4S、Turbo、GT2、GT3
保时捷 982(718) Boxster / Boxster S
保时捷 982(718)Cayman / Cayman S
可选的 RSS 锁定板套件设计用于 RSS 可调后束/碰撞转向套件(零件编号 312) 。
该套件取代了在赛车和/或激烈驾驶条件下可能松动的工厂偏心螺栓。
相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号,供比较之用。
333
您正在查看的产品与这些编号存在交叉引用关系
- Porsche Boxster 986 2.5L 1997-99
- Porsche Boxster 986 2.7L 1999-02
- Porsche Boxster S 986 3.2L 1999-02
- Porsche Boxster 986 2.7L 2003-04
- Porsche Boxster S 986 3.2L 2003-04
- Porsche Boxster 987 2.7L 2005 -08/08
- Porsche Boxster 987 S 3.2/3.4L 2005-08/08
- Porsche Boxster 987 MKII 2.9L 2009-2012
- Porsche Boxster S 987 MKII 3.4L 2009-2012
- Porsche Boxster 981 2.7L 2012-16
- Porsche Boxster S 981 3.4L 2012-16
- Porsche Boxster 718 2.0L Manual (300 Bhp)
- Porsche Boxster 718 2.0L PDK (300 Bhp)
- Porsche Boxster S 718 2.5L Manual (350 Bhp)
- Porsche Boxster S 718 2.5L PDK (350 Bhp)
- Porsche 996 C2 3.4L 1997-08/01
- Porsche 996 C4 3.4L 1997-08/01
- Porsche 996 C2 3.6L 09/01-2005
- Porsche 996 C4 3.6L 09/01-2005
- Porsche 996 C4S 3.6L 09/01-2005
- Porsche 996 TURBO 2000-05
- Porsche 996 GT2 2001-05
- Porsche 996 GT3 MKI 1999-02
- Porsche 996 GT3 MKII 2003>>
- Porsche 996 GT3 RS 2003-04
- Porsche 997 Carrera 2 3.6L 2005>>
- Porsche 997 Carrera 2S 3.8L 2005>>
- Porsche 997 Carrera 4 3.6L 2005>>
- Porsche 997 Carrera 4S 3.8L 2005>>
- Porsche 997 TURBO 2007>>
- Porsche 997 GT3 2007>>
- Porsche 997 GT2 2007>>
- Porsche 997 MKII Carrera C2 3.6L 2009>>
- Porsche 997 MKII Carrera C4 3.6L 2009>>
- Porsche 997 MKII Carrera C2S 3.8L 2009>>
- Porsche 997 MKII Carrera C4S 3.8L 2009>>
- Porsche 991 Carrera C2 3.4L (350Bhp)
- Porsche 991 Carrera C2S 3.8L (400Bhp)
- Porsche 991 Carrera C4 3.4L (350Bhp)
- Porsche 991 Carrera C4S 3.8L (400Bhp)
- Porsche 991 Turbo 3.8L (520bhp)
- Porsche 991 Turbo S 3.8L (560Bhp)
- Porsche 991 R 4.0L (500 Bhp)
- Porsche 991 GT3 3.8L (475Bhp)
- Porsche 991 GT3 RS 4.0L (500Bhp)
- Porsche 991 Carrera 2 3.0L (370 Bhp)
- Porsche 991 Carrera 2S 3.0L (420 Bhp)
- Porsche 991 Carrera 4 3.0L (370 Bhp)
- Porsche 991 Carrera 4S 3.0L (420 Bhp)
- Porsche 991 Cabriolet 2 3.0L (370 Bhp)
- Porsche 991 Cabriolet 2S 3.0L (420 Bhp)
- Porsche 991 Cabriolet 4 3.0L (370 Bhp)
- Porsche 991 Cabriolet 4S 3.0L (420 Bhp)
- Porsche 991 Targa 4 3.0L (370 Bhp)
- Porsche 991 Targa 4S 3.0L (420 Bhp)
- Porsche 991 Turbo Coupe 3.8L (540 Bhp)
- Porsche 991 Turbo S Coupe 3.8L (580 Bhp)
- Porsche 991 Turbo Cabriolet 3.8L (540 Bhp)
- Porsche 991 Turbo S Cabriolet 3.8L (580 Bhp)
- Porsche 991 GT3 4.0L (500 Bhp) / GT3 RS 4.0L (520 Bhp)
- Porsche 991 GT2 RS 3.8L PDK (700 bhp)
- Porsche Cayman 2.7L 987C 2006-08
- Porsche Cayman S 3.4L 987C 2005-08
- Porsche Cayman 2.9L 987C MKII 2009-12
- Porsche Cayman S / R 3.4L 987C MKII 2009-12
- Porsche Cayman 2.7L 981 2013-16
- Porsche Cayman S 3.4L 981 2013-16
- Porsche Cayman GT4 3.8L 2015-16
- Porsche Cayman 718 2.0L Manual (300Bhp)
- Porsche Cayman 718 2.0L PDK (300Bhp)
- Porsche Cayman S 718 2.5L Manual (350Bhp)
- Porsche Cayman S 718 2.5L PDK (350Bhp)
1 kit required per axle
Fits
Porsche 986 Boxster - Front and Rear
Porsche 987 Boxster and Cayman - Front and Rear
Porsche 996 - Front and Rear
Porsche 997 - Front and Rear
Porsche 981 - Front and Rear
Porsche 718 - Front and Rear
Porsche 991 - Front Only
Porsche 992 - Front Only
* Not For '12+ 991, 992 GT3/GT4
GT3 Street Inner Spherical Bearing Module
Unlike the factory rubber bushed GT3 inner control arms, our spherical bearings do not deflect under load.
They are fully weather sealed to keep out water and grit for extended life.
• Use in combination with factory GT3 street type control arm only
• Does not fit 991 GT3 or GT4 arms
• Easy Bolt-On
• Weather-sealed
• Sold as pair
• Front and Rear for 996, 997, 986, 987, 981, 718
• Front only on 991
相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号,供比较之用。
2180030
您正在查看的产品与这些编号存在交叉引用关系
- Porsche Boxster 986 2.5L 1997-99
- Porsche Boxster 986 2.7L 1999-02
- Porsche Boxster S 986 3.2L 1999-02
- Porsche Boxster 986 2.7L 2003-04
- Porsche Boxster S 986 3.2L 2003-04
- Porsche Boxster 987 2.7L 2005 -08/08
- Porsche Boxster 987 S 3.2/3.4L 2005-08/08
- Porsche Boxster 987 MKII 2.9L 2009-2012
- Porsche Boxster S 987 MKII 3.4L 2009-2012
- Porsche Boxster 718 2.0L Manual (300 Bhp)
- Porsche Boxster 718 2.0L PDK (300 Bhp)
- Porsche Boxster S 718 2.5L Manual (350 Bhp)
- Porsche Boxster S 718 2.5L PDK (350 Bhp)
- Porsche Boxster T 718 2.0L Manual (300 Bhp)
- Porsche Boxster T 718 2.0L PDK (300 Bhp)
- Porsche Boxster GTS 718 2.5L Manual (365 Bhp)
- Porsche Boxster GTS 718 2.5L PDK (365 Bhp)
- Porsche Boxster GTS 718 4.0L Manual (400 Bhp)
- Porsche Boxster GTS 718 4.0L PDK (400 Bhp)
- Porsche Boxster Spyder 718 4.0L (420 Bhp)
- Porsche Boxster 25 Years 718 4.0L Manual (400 Bhp)
- Porsche Boxster 25 Years 718 4.0L PDK (400 Bhp)
- Porsche 996 C2 3.4L 1997-08/01
- Porsche 996 C4 3.4L 1997-08/01
- Porsche 996 C2 3.6L 09/01-2005
- Porsche 996 C4 3.6L 09/01-2005
- Porsche 996 C4S 3.6L 09/01-2005
- Porsche 996 TURBO 2000-05
- Porsche 996 GT2 2001-05
- Porsche 996 GT3 MKI 1999-02
- Porsche 996 GT3 MKII 2003>>
- Porsche 996 GT3 RS 2003-04
- Porsche 997 Carrera 2 3.6L 2005>>
- Porsche 997 Carrera 2S 3.8L 2005>>
- Porsche 997 Carrera 4 3.6L 2005>>
- Porsche 997 Carrera 4S 3.8L 2005>>
- Porsche 997 TURBO 2007>>
- Porsche 997 GT3 2007>>
- Porsche 997 GT2 2007>>
- Porsche 997 MKII Carrera C2 3.6L 2009>>
- Porsche 997 MKII Carrera C4 3.6L 2009>>
- Porsche 997 MKII Carrera C2S 3.8L 2009>>
- Porsche 997 MKII Carrera C4S 3.8L 2009>>
- Porsche 997 MKII GT3 2010>>
- Porsche 997 MKII Turbo 2009>>
- Porsche 997 MKII GT2 RS 2011>>
- Porsche 991 Carrera C2 3.4L (350Bhp)
- Porsche 991 Carrera C2S 3.8L (400Bhp)
- Porsche 991 Carrera C4 3.4L (350Bhp)
- Porsche 991 Carrera C4S 3.8L (400Bhp)
- Porsche 991 Turbo 3.8L (520bhp)
- Porsche 991 Turbo S 3.8L (560Bhp)
- Porsche 991 Carrera 2 3.0L (370 Bhp)
- Porsche 991 Carrera 2S 3.0L (420 Bhp)
- Porsche 991 Carrera 4 3.0L (370 Bhp)
- Porsche 991 Carrera 4S 3.0L (420 Bhp)
- Porsche 991 Cabriolet 2 3.0L (370 Bhp)
- Porsche 991 Cabriolet 2S 3.0L (420 Bhp)
- Porsche 991 Cabriolet 4 3.0L (370 Bhp)
- Porsche 991 Cabriolet 4S 3.0L (420 Bhp)
- Porsche 991 Targa 4 3.0L (370 Bhp)
- Porsche 991 Targa 4S 3.0L (420 Bhp)
- Porsche 991 Turbo Coupe 3.8L (540 Bhp)
- Porsche 991 Turbo S Coupe 3.8L (580 Bhp)
- Porsche 991 Turbo Cabriolet 3.8L (540 Bhp)
- Porsche 991 Turbo S Cabriolet 3.8L (580 Bhp)
- Porsche 992 Carrera 2 3.0L
- Porsche 992 Carrera 4 3.0L
- Porsche 992 Carrera 2 Cabriolet 3.0L
- Porsche 992 Carrera 4 Cabriolet 3.0L
- Porsche 992 Carrera 2S 3.0L
- Porsche 992 Carrera 4S 3.0L
- Porsche 992 Carrera 2S Cabriolet 3.0L
- Porsche 992 Carrera 4S Cabriolet 3.0L
- Porsche 992 Targa 4 3.0L
- Porsche 992 Targa 4S 3.0L
- Porsche 992 Turbo 3.8L
- Porsche 992 Turbo S 3.8L
- Porsche 992 Turbo Cabriolet 3.8L
- Porsche 992 Turbo S Cabriolet 3.8L
- Porsche Cayman 2.7L 987C 2006-08
- Porsche Cayman S 3.4L 987C 2005-08
- Porsche Cayman 2.9L 987C MKII 2009-12
- Porsche Cayman S / R 3.4L 987C MKII 2009-12
- Porsche Cayman 2.7L 981 2013-16
- Porsche Cayman S 3.4L 981 2013-16
- Porsche Cayman 718 2.0L Manual (300Bhp)
- Porsche Cayman 718 2.0L PDK (300Bhp)
- Porsche Cayman S 718 2.5L Manual (350Bhp)
- Porsche Cayman S 718 2.5L PDK (350Bhp)
- Porsche Cayman T 718 2.0L Manual (300Bhp)
- Porsche Cayman T 718 2.0L PDK (300 Bhp)
- Porsche Cayman GTS 718 2.5L Manual (365 Bhp)
- Porsche Cayman GTS 718 2.5L PDK (365 Bhp)
- Porsche Cayman GTS 718 4.0L Manual (400 Bhp)
- Porsche Cayman GTS 718 4.0L PDK (400 Bhp)
1 kit required per car
Fits
Porsche 991 2012 Onward - Rear Only
These monoball cartridges replace factory rear upper control arm bushings with hardened-steel spherical bearings. Spherical bearings allow free motion on multiple axis and eliminate deflection associated with rubber, resulting in more precise holding of toe and camber.High tolerance machined housing allow for simple press fit installation. Correct spacers ensure proper fitment.
Weather Sealed
Monoball housing and spacers are hard anodized for protection. Our proprietary rubber seals keep the precision bearing from road contaminates for extended life of the product.
The kit includes 8 monoball bearings. 2 per arm, for 4 arms total.
Order one kit per car.
相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号,供比较之用。
2260007
您正在查看的产品与这些编号存在交叉引用关系
- Porsche 991 Carrera C2 3.4L (350Bhp)
- Porsche 991 Carrera C2S 3.8L (400Bhp)
- Porsche 991 Carrera C4 3.4L (350Bhp)
- Porsche 991 Carrera C4S 3.8L (400Bhp)
- Porsche 991 Carrera 2 3.0L (370 Bhp)
- Porsche 991 Carrera 2S 3.0L (420 Bhp)
- Porsche 991 Carrera 4 3.0L (370 Bhp)
- Porsche 991 Carrera 4S 3.0L (420 Bhp)
- Porsche 991 Cabriolet 2 3.0L (370 Bhp)
- Porsche 991 Cabriolet 2S 3.0L (420 Bhp)
- Porsche 991 Cabriolet 4 3.0L (370 Bhp)
- Porsche 991 Cabriolet 4S 3.0L (420 Bhp)
- Porsche 991 Targa 4 3.0L (370 Bhp)
- Porsche 991 Targa 4S 3.0L (420 Bhp)
使用可调后控制臂升级您的保时捷悬架:技术规格和优势
可调式后控制臂的技术规格:
- 可调节后控制臂是悬架部件,旨在对车辆的后悬架几何形状进行精确调整。
- 它们通常由高强度钢或轻质合金制成,以提高耐用性和性能。
- 可调节后控制臂具有螺纹或偏心支架,可以对外倾角和前束设置进行微调。
- 它们具有各种设计和长度,以适合不同的保时捷车型和悬架设置。
- 可调节后控制臂可作为保时捷车辆的升级选项或标准替代品。
升级或更换保时捷可调后控制臂的好处:
增强的后悬架几何结构:可调节的后控制臂允许精确调整外倾角和前束角,优化后悬架几何结构,以改善操控性、稳定性和轮胎磨损。
改善转弯性能:通过微调后悬架设置,可调节控制臂可以帮助减少转向不足或转向过度的趋势,增强车辆的转弯能力和整体平衡。
增加牵引力和抓地力:通过可调节控制臂实现后轮的正确定位,确保轮胎与路面最佳接触,从而提高牵引力、抓地力和加速度。
最大限度地减少轮胎磨损:通过保持正确的后部对齐,可调节的控制臂有助于防止轮胎磨损不均匀并延长轮胎的使用寿命,从长远来看可以为您节省费用。
可定制性和适应性:可调节后控制臂可以灵活地调整后悬架设置,以适应特定的驾驶偏好、轨道条件或对车辆的修改。
在 Design911,我们专门为您的保时捷提供正确的零件和专业建议。我们提供专为保时捷车型设计的各种可调后控制臂,包括 OEM 更换和性能升级。我们知识渊博的团队致力于帮助您找到适合您的保时捷的控制臂,考虑车型、年份、悬架设置和所需调整等因素。凭借我们的专业知识和对客户满意度的承诺,我们可以指导您选择完美的控制臂,以增强您的保时捷的悬架性能和操控特性。立即联系我们,享受我们的全面支持并获得根据您的需求量身定制的高质量零件。
- 支撑架
- 防侧翻稳定杆
- 运动弹簧
- 前控制臂
- 前悬挂连接杆
- 后悬挂连接杆
- 前侧车顶支架
- 后侧车顶支架
- 转向横拉杆
- 后副车架
- 气动升降系统
- 悬架控制单元
- Bilstein B4 标准替换件
- Bilstein B4(带 PASM 按钮的车辆)
- Bilstein SPORT B6 减震器
- Bilstein SPORT B6(带 PASM 按钮的车辆)
- Bilstein B14 PSS 避震悬架套件
- Bilstein B16 PSS9/10 高度减震可调避震悬架套件
- Bilstein B16 DampTronic (PASM)
- Bilstein EVO SE
- Ohlins 道路及赛道悬架
- Powerflex 聚氨酯衬套
- Powerflex 黑色系列衬套
- H&R 可调悬架套件
- H&R Cup-Kit 系列运动悬架
- KW 高度可调弹簧
- KW 变体 1 Inox 悬架套件
- KW 变体 2 Inox 可调回弹减震悬架
- KW 变体 3 Inox 可调悬架套件
- KW Clubsport 避震悬架套件
- KW Clubsport 避震悬架套件(带车顶支架)
- KW HLS(液压升降系统)
- KW DDC(带 ECU 避震悬架套件)
- Eibach Pro-Tronic PASM 拆卸套件
- Sachs 高性能悬架 CSS
- Arnott 欧洲空气悬架产品