Driveshaft, Rear. Porsche 992 GT3  ❭  9GT501201G

Reconditioned Driveshaft, Rear
Fitting Position: Rear Axle Left, Rear Axle Right 
Sold individually, 1 required per side where fitted, 2 required per vehicle if replacing both rear drive shafts.

Please note:
Reconditioned units are sold on an exchange basis, A surcharge of £75.00 will be held and then refunded when the old one is returned. The old unit must be returned to Design911 in a built state, not in component pieces.

Fits:
Porsche 911 (992) GT3 (992810, 992812)  05.2021-12.2025 Coupe
Porsche 911 (992) GT3 RS (992850)  09.2022-12.2025 Coupe
Porsche 911 (992) GT3 Touring (992820, 992822) 05.2021-12.2025 Coupe
Porsche 911 (992) S/T  (992880)   06.2023-12.2025 Coupe

Diagram ref no 1

Length: 541 mm
Seal diam.: 64 mm
Wheel Side Joint Ø: 105 mm
Transmission-sided Joint Ø: 116 mm
Thread Size: M22x1.5
Bore Ø: 11 mm
Number of bores: 6 Bolt
Hole Circle Ø: 100 mm
Exchange Part
Supplementary Article: with nut

High-quality GKN rear driveshaft for the Porsche 911 Type 992 GT3, designed as a premium replacement for Porsche OE references 9GT501201A and 9GT501201G.

The GKN GKND13208 complete driveshaft assembly transfers engine torque from the transmission and differential to the driven rear wheels while allowing for continuous suspension movement and changes in driveshaft angle.

Designed for installation on either the left-hand or right-hand side of the rear axle, the same driveshaft can be used for both positions.

Porsche reference 9GT501201G supersedes the earlier 9GT501201A reference.

GKN Automotive is one of the world's leading specialists in constant-velocity joint and sideshaft technology. Its aftermarket drivetrain components benefit directly from the company's OE engineering expertise and are designed to provide dependable torque transmission, durability and excellent Noise, Vibration and Harshness performance.

Why Replace a Worn Drive Shaft?
The driveshaft and CV joints operate under considerable load and are subjected to constant movement as the vehicle accelerates, brakes and travels over changing road surfaces.

Over time, wear or damage can occur to the CV joints, shaft, boots or associated components.

Possible symptoms of a worn or damaged rear driveshaft include:  
•  Clicking or knocking noises
•  Vibration during acceleration
•  Shuddering through the vehicle
•  Excessive driveline play
•  Noise when turning
•  Damaged or leaking CV boots
•  Grease loss around the CV joint
•  Mechanical noise under acceleration or regenerative load.

Replacing a worn assembly with a complete quality GKN driveshaft helps restore smooth and reliable torque transmission.


PLEASE NOTE:

• The surcharge for this reconditioned part will be refunded when the exchange unit is received and approved by us and the relevant manufacturer.
• Please note, surcharge refunds often take an average of 6 to 8 weeks to be approved by the manufacturer.
• Acceptance of the exchange part is at the manufacturer's discretion, based on the part being fit for reconditioning.
• All surcharges and exchanges are subject to our terms and conditions.      

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

9GT501201G

The product you are viewing cross references to these numbers
PLEASE NOTE:
Due to its size, weight or fragility, this item requires additional protective packaging to make sure it reaches you undamaged. A small packing surcharge is applied to cover these specialist materials and the extra care taken preparing your order for transit.