Front Undertray. Porsche 964 C4 / 993 C4  ›  96450412700

Rubber drain pipe at bottom of headlamp bucket and floor pan.

Fits:
Porsche 911/912 1965-1989

Diagram ref no 44

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

91102561200

The product you are viewing cross references to these numbers

Rubber Drain Grommet
Sold each

The OE Match Rubber Drain Grommet is a replacement bodywork component for compatible Porsche 911 and 912 models.

Fits:

• Porsche 911 1965-1968 2.0L / 912 SWB (F)
• Porsche 911 1968-1973 2.2L / 2.4L / 2.7L RS LWB (F)
• Porsche 911 1974-1977 2.7L / 1976-77 3.0 Carrera
• Porsche 911 1978-1983 3.0L / SC
• Porsche 911 1984-1986 3.2L
• Porsche 911 1987-1989 3.2L G50
• Porsche 911 1975-1977 3.0L Turbo (930)
• Porsche 911 1978-1989 3.3L Turbo (930)

Diagram ref no 44

Designed to fit the corresponding drainage opening, this rubber grommet helps maintain the original drainage arrangement, allowing collected water to escape while providing a protective fitting around the opening.

Over time, original rubber components can harden, crack or deteriorate, making replacement an important part of classic Porsche maintenance and restoration.

What Does It Do?

The rubber drain grommet fits into a designated bodywork drainage opening, helping direct water away from areas where moisture could otherwise accumulate.

It also provides a protective rubber fitting around the opening.

Why Does It Fail?

Common causes of deterioration include:

• Age-related rubber hardening
• Cracking from temperature changes
• Exposure to moisture and road contamination
• Damage during removal or bodywork repairs
• General deterioration after prolonged use

When Should It Be Replaced?

Replace the grommet if it becomes cracked, brittle, distorted or missing.

Replacement is also recommended during bodywork restoration, particularly where the original drainage components have deteriorated.

Checks & Diagnosis

Inspect the grommet for damage and check that the associated drainage opening is clear of dirt and debris.

Look for trapped moisture or signs of corrosion around the mounting area.

Installation Notes

Remove the deteriorated grommet and clean the mounting opening before fitting the replacement. Ensure the grommet is seated correctly and the drainage passage remains unobstructed.

Porsche 911 & 912 Rubber Grommets and Bodywork Drainage Parts

Rubber drain grommets are small but important components used in classic Porsche bodywork to help manage water drainage and protect designated openings.

OE Match rubber drain grommet 91102561200 provides a replacement for compatible Porsche 911 and 912 models, helping maintain the original drainage arrangement during servicing or restoration.

Design911 supplies Porsche rubber grommets, body seals, drainage components and associated classic Porsche restoration parts.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

91102561200

The product you are viewing cross references to these numbers

Aluminium skid plate.

A lowered ride height is a must for any car used on the track or for performance street driving. The biggest down side to this modification is ground clearance. Speed bumps, pot holes or the occasional "Off Track" excursion can cause some serious damage to the underside of your car. The Rennline Aluminum Skid Plates have been designed to eliminate those concerns. Rennline's skid plate conceals the entire underside of the fuel tank as well as the fuel pump, steering rack, and much of the front control arm and are formed so that no edges will get caught on objects when traveling forward, backwards or sideways. Hardware is included and installation takes about 5 minutes with no drilling required.

These skid plates work with factory or Rennline front tie downs, and will also work with a 100L fuel tank.

Compatible with '78-'89 911/930 or earlier cars with the later aluminum cross member. Will not work on cars with front condenser.