Boots / Rear Lid / Locks and Latches

REAR lid release cable
This OE Match rear lid release cable is a replacement engine lid / rear decklid release cable for Porsche 911 models from 1965 to 1989 and Porsche 964 models. It is designed to match the original-style fitment and function, helping restore smooth and reliable rear lid opening.

Fits:
Porsche 911 1965 - 1989 REAR
Porsche 911 (930) Turbo 1978 - 1989 REAR 
Porsche 964 1989 - 1994 REAR

This product supersedes Porsche's old part numbers:
- 90151107320

Diagram ref no 37

The rear lid release cable connects the interior release handle or lever to the rear lid latch mechanism. When operated, the cable pulls the latch release, allowing the rear engine lid to open. A correctly working release cable is essential for access to the engine bay and rear service area.

Functions
• Connects the rear lid release control to the latch mechanism
• Allows the rear engine lid / decklid to open correctly
• Transfers pull movement from the cabin release to the rear latch
• Helps restore smooth and reliable lid release operation
• Replaces stretched, seized, frayed, snapped, or damaged original cables
• Supports correct access to the engine compartment
• OE Match replacement for body, trim, and latch system repair

Why Replace This Part?
Rear lid release cables can stretch, fray, seize, corrode, snap, or become stiff over time due to age, moisture, dirt, and repeated use. A worn or damaged cable may make the rear lid difficult to open, may require excessive force, or may fail completely and prevent access to the engine bay. Replacing the cable helps restore dependable rear lid release operation and correct classic Porsche functionality.

When to Replace This Part
•  The rear lid release cable is stretched, seized, frayed, or snapped
•  The rear engine lid is difficult to open
•  The release handle feels loose, stiff, or has excessive travel
•  The latch does not release consistently
•  The cable outer casing is damaged or corroded
•  The rear lid latch or release handle is being serviced
•  The vehicle is undergoing Porsche 911 or 964 bodywork restoration

Where it fits on the car
This cable fits within the rear lid release system, running between the release control and the rear lid latch mechanism. It is used to operate the engine lid / rear decklid latch on Porsche 911 and 964 models.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

90151107321

The product you are viewing cross references to these numbers

Rear lid rubber washer spacer



Fits:
Porsche 911 1974-89

Click 'Zoom in' for large parts diagram.
Diagram ref no 8

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

91155943500

The product you are viewing cross references to these numbers

Rear lid washer.



Fits:
Porsche 911 1974-89

Click 'Zoom in' for large parts diagram.
Diagram ref no 9

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

113951539

The product you are viewing cross references to these numbers

Rear lid, aluminium.



Fits:
Porsche 911 F model 1969-73

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

91151201000

The product you are viewing cross references to these numbers

Reinforcement strip for rear spoiler. Sold each.



Fits:
Porsche 911 1974-80

Click 'Zoom in' for parts diagram.
Diagram Ref no 10

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

91151228300

The product you are viewing cross references to these numbers

Reinforcement strip for rear spoiler. Sold each.



Fits:
Porsche 911 1974-80

Click 'Zoom in' for parts diagram.
Diagram Ref no 13

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

91151228400

The product you are viewing cross references to these numbers

Rennline titanium 911R style engine lid hinge set. 



Fits:
Porsche 911 - 1964 to 1989

Save weight and add style to your 911 with our 911R Decklid Hinge

The only titanium 911R decklid hinge on the market, this hinge is guaranteed to be the lightest and most durable option available.

Product Description

Convert your standard 911 decklid to the 911R “Flip over” style with our 911R inspired titanium decklid hinges. 
This kit includes a unique backing piece that forms to the contour of your decklid for a simple, easy installation. 

• Titanium Design
• Stainless Steel Hardware
• Unique Backing bracket to support third mounting hole on engine lid (decklid)
• Does not work with decklid struts
• Quick release Clevis Pin

Please Note:
Requires drilling to car as well as the engine lid (decklid)
Fitment on aftermarket engine lids is not guaranteed

Spoiler Rubber. The Lid is not included.



Fits:
Porsche 911 1984-89 (not Turbo)
It will fit any car fitted with Carrera Tail Spoiler

Click picture for large parts diagram.
Diagram Ref: 16

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

9115120910101C

The product you are viewing cross references to these numbers

Rubber Stop For Rear Lid.

The OE Match Rubber Stop for Rear Lid is a replacement rubber buffer designed to support and cushion the rear lid when closed.

Fits:

• Porsche Boxster 986 2.5L 1997-99
• Porsche Boxster 986 2.7L 1999-02
• Porsche Boxster S 986 3.2L 1999-02
• Porsche Boxster 986 2.7L 2003-04
• Porsche Boxster S 986 3.2L 2003-04
• Porsche Boxster 987 2.7L 2005-08/08
• Porsche Boxster 987 S 3.2/3.4L 2005-08/08
• Porsche 911 1974-1977 2.7L / 1976-77 3.0 Carrera
• Porsche 911 1978-1983 3.0L / SC
• Porsche 911 1984-1986 3.2L
• Porsche 911 1987-1989 3.2L G50
• Porsche 911 1975-1977 3.0L Turbo (930)
• Porsche 911 1978-1989 3.3L Turbo (930)
• Porsche 996 C2 3.4L 1997-08/01
• Porsche 996 C4 3.4L 1997-08/01
• Porsche 996 C2 3.6L 09/01-2005
• Porsche 996 C4 3.6L 09/01-2005
• Porsche 996 C4S 3.6L 09/01-2005
• Porsche 996 TURBO 2000-05
• Porsche 996 GT2 2001-05
• Porsche 996 GT3 MKI 1999-02
• Porsche 996 GT3 MKII 2003>>
• Porsche 996 GT3 RS 2003-04
• Porsche 997 MK1 Carrera 2 3.6L 2005-08
• Porsche 997 MK1 Carrera 2S 3.8L 2005-08
• Porsche 997 MK1 Carrera 4 3.6L 2005-08
• Porsche 997 MK1 Carrera 4S 3.8L 2005-08
• Porsche 997 MK1 TURBO 2007-09
• Porsche 997 MK1 GT3 / GT3 RS 2007-09
• Porsche 997 MK1 GT2 2007-09
• Porsche 997 MKII Carrera C2 3.6L 2009-12
• Porsche 997 MKII Carrera C4 3.6L 2009-12
• Porsche 997 MKII Carrera C2S 3.8L 2009-12
• Porsche 997 MKII Carrera C4S 3.8L 2009-12
• Porsche 997 MKII GT3 / GT3 RS 2010-11
• Porsche 997 MKII Turbo 2010-13
• Porsche 997 MKII GT2 RS 2011-13
• Porsche Cayman 2.7L 987C 2006-08
• Porsche Cayman S 3.4L 987C 2005-08
• Porsche Cayman 2.9L 987C MKII 2009-12
• Porsche Cayman S / R 3.4L 987C MKII 2009-12
• Porsche 944 2.5L 8V 1982-87
• Porsche 944 2.7L 8V 1988-89
• Porsche 944S 2.5L 16V 1987-88
• Porsche 944S2 3.0L 16V 1989-91
• Porsche 944 Turbo 2.5L 8V 1985-88
• Porsche 944 Turbo 2.5L 8V 1989-91
• Porsche 944 Turbo S 2.5L 8V 1988
• Porsche 968 3.0L 1992-94
• Porsche 968 Sport 3.0L 1994-95
• Porsche 968 CS 3.0L 1993-95
• Porsche 968 Turbo S 3.0L 1993-94
• Porsche 928 4.5L 1978-82
• Porsche 928S 4.7L 1981-83
• Porsche 928S2 4.7L 1984-86
• Porsche 928S4 5.0L 1987-92
• Porsche 928GT 5.0L 1989-91
• Porsche 928GTS 5.4L 1992-95  

Diagram Ref No 39

Mounted at the rear lid or body contact point, the rubber stop helps prevent direct metal-to-metal contact while supporting correct lid positioning. It also helps absorb vibration and minor movement when driving, reducing rattles and protecting surrounding bodywork and latch components from unnecessary impact.

As rubber components age, they can harden, crack, flatten or disappear altogether. Replacing a deteriorated rear lid stop is a simple but important way to restore correct closure, reduce unwanted noise and maintain proper panel positioning.

What This Product Does:
The rear lid rubber stop acts as a small cushioning and support point between the lid and surrounding body structure.

When the lid is closed, the stop compresses slightly to support the panel and absorb movement. This helps keep the lid stable while preventing hard contact between painted or metal components.

Its main functions include:

• Cushioning the rear lid when it closes
• Preventing direct metal-to-metal contact
• Helping support correct rear lid positioning
• Reducing movement and vibration while driving
• Helping prevent rattles and knocking noises
• Protecting surrounding paintwork and body panels
• Reducing unnecessary load and movement at the latch
• Helping maintain consistent panel gaps
• Providing a more solid and refined closing action

Although it is a small component, the rubber stop contributes to both correct panel fit and everyday refinement.

Symptoms Of Wear Or Failure:
Rubber stops deteriorate naturally through age, heat, compression and exposure to moisture and environmental contaminants.

Common symptoms of a worn or failed rear lid rubber stop include:

• Rubber becoming hard or brittle
• Cracks or splits in the stop
• Stop becoming flattened or permanently compressed
• Pieces of rubber breaking away
• Stop missing completely
• Rear lid rattling over uneven roads
• Knocking or tapping noises from the rear lid
• Excessive movement when the lid is closed
• Lid sitting slightly too low or unevenly
• Poor or inconsistent panel gaps
• Rear lid requiring adjustment to close correctly
• Paint marks or contact points where the lid touches surrounding bodywork
• Increased strain or movement at the latch
• A harsher closing action than normal

Similar symptoms can also result from incorrect latch adjustment, worn hinges or other missing buffers, so the complete rear lid mounting and closure system should be inspected where necessary.

Why Replacement Matters:

• A rear lid should remain securely supported when closed. If the rubber stop becomes compressed, hardened or missing, the panel can move more than intended.
• This movement can create rattles and knocking noises and may allow the lid to contact surrounding bodywork. Over time, repeated contact can damage paintwork and create unnecessary wear around the lid, latch and mounting points.
• A deteriorated stop can also affect how the rear lid sits when closed, potentially resulting in uneven panel gaps or poor alignment.
• Replacing worn rubber stops helps restore the correct cushioning effect and supports the lid in its intended position. This can improve closure quality, reduce unwanted vibration and protect valuable surrounding bodywork.
• For older Porsche models, replacing aged rubber buffers is also worthwhile during restoration, as decades-old rubber may appear intact while having become significantly hardened or compressed.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

99970314040

The product you are viewing cross references to these numbers

Rubber stop for front bonnet / rear lid.


Porsche 911 2.0-3.3 1965-89
Porsche 912 1.6 01/65-02/70
Porsche 914 1.7-2.0 01/69-02/76


Porsche 911 2.0-3.3 1965-73
Porsche 912 1.6 01/65-02/70
Porsche 914 1.7-2.0 01/69-02/76

Diagram ref no 22

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

99970303650

The product you are viewing cross references to these numbers

Smuggler's Box Cover Seal for Left Hand Drive Cars Only



Fits:
Porsche 911 1965-89

Click 'Zoom in' for large parts diagram.
Diagram ref no 22

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

91150449102

The product you are viewing cross references to these numbers

Smuggler's box cover seal for Left Hand Drive Cars Only
This OE Match smuggler’s box cover seal is a replacement rubber sealing strip used on left-hand drive Porsche 911 models. It fits around the smuggler’s box cover panel in the front luggage compartment, helping seal the cover correctly against the body.  

Fits:
Porsche 911 1965 - 1989

Diagram ref no 22

The smuggler’s box cover seal helps close the gap between the cover and the surrounding body panel. It prevents water, dust, dirt, and road debris from entering the compartment area and helps reduce vibration or rattling from the cover panel.

Functions
•  Seals the smuggler’s box cover in the front luggage compartment
•  Helps prevent water, dust, and dirt entering the compartment
•  Reduces cover panel vibration and rattling
•  Provides a clean OE-style finish around the cover edge
•  Helps protect components housed in or near the smuggler’s box area
•  Replaces worn, cracked, flattened, or missing original seals
•  Suitable for restoration, bodywork repair, or front trunk refurbishment

Why Replace This Part?
Original rubber seals can harden, shrink, split, flatten, or perish with age. A damaged or missing smuggler’s box cover seal may allow moisture and dirt into the compartment and can make the cover sit poorly or rattle. Replacing the seal helps restore the correct factory-style fit, improves protection, and gives the front luggage area a cleaner finished appearance.

When to replace:
•  The original seal is cracked, brittle, flattened, or missing
•  Water, dust, or dirt is entering the smuggler’s box area
•  The cover panel rattles or does not sit correctly
•  The front luggage compartment is being restored
•  The smuggler’s box cover has been removed or replaced
•  The vehicle is undergoing bodywork, repainting, or seal replacement
•  You want to restore the correct OE-style front trunk finish

Where it fits on the car
This seal fits around the smuggler’s box cover panel in the front luggage compartment of left-hand drive Porsche 911 models. The smuggler’s box is located under the front trunk floor area and houses or protects various vehicle components depending on model year and specification.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

91150449102

The product you are viewing cross references to these numbers

Spoiler Rear Rubber.


Fits:
Porsche 911 1974-80

Click 'Zoom in' for parts diagram.
Diagram Ref no 1

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

91151201902

The product you are viewing cross references to these numbers

Spoiler Rubber for 'Tea Tray' spoiler.



Fits:
Porsche 930 3.3L Turbo 1981-89
Porsche 911 1974-89 with Turbo spoiler



Click picture for parts diagram.
Diagram Ref: 16

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

93051202101

The product you are viewing cross references to these numbers

Rennline's billet T-handle pulls are the perfect inexpensive interior upgrade for any Porsche equipped with this feature. Factory pulls become weak, cracked, and/or unsightly after years of use and exposure to UV light. Rennline billet T-handles are machined from 6061 aluminum and black anodized for a durable, long lasting appearance. Simply unscrew your old pull and screw ours on.



Fits:
Porsche 911/912/930 (1965-1989)

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

I54

The product you are viewing cross references to these numbers

T-Headed Screw for Rear Lid Grille. 6 per grille. Sold each.

Fits:
Porsche 911 1974-89

Diagram ref no 15

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

91155943300

The product you are viewing cross references to these numbers