Targa

Rear of roll bar seal.

Fits:
Porsche 911 1965-89
Porsche 964 1989-94

Diagram Ref: 23

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

90156593041

The product you are viewing cross references to these numbers

Rear of roll bar seal.
The rear window to roll bar seal acts as a critical weather barrier, preventing water, wind, and road debris from entering the cabin around the rear glass area. It also helps reduce wind noise and ensures that the Targa top assembly fits cleanly and snugly, maintaining the iconic look and function of the Porsche Targa design.

Fits:
Porsche 911 1965 - 1989
Porsche 964 1989 - 1994

Diagram ref no 23

• Application: Fits rear glass to roll bar sealing interface on classic Targa cars. One seal per car. Designed to match original factory dimensions and mounting locations for a direct replacement fit.
• Function: Weatherproofing between rear glass & roll bar
• Benefits: Prevents leaks, reduces noise, restores original fit & finish

Installed along the top edge of the rear glass where it meets the Targa roll bar, this gasket provides a consistent sealing surface that keeps out moisture and airflow while preserving the structural integrity and classic silhouette of your Porsche. It supports long-term durability for road driving and contributes to the car’s overall comfort and weather resistance. 

Over time, the original rear window seal can harden, crack, or compress due to aging, UV radiation, and temperature fluctuations. When the seal isn't functioning properly, moisture can leak into or into the cabin, causing water spots, fogging, and potential corrosion. Replacing this seal with a new, high-quality seal restores proper weather protection, keeps the interior dry and quiet, and helps preserve the value and authenticity of your classic Porsche.

Replace the rear Targa roll bar seal if you notice:
• Cracks, splits, or visible hardening of the seal
• Water leaks or dampness around the rear window
• Increased wind noise at higher speeds
• Loose or compressed seal no longer providing firm contact
• During restoration or Targa top refurbishment

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

90156593041

The product you are viewing cross references to these numbers

Rear roll bar seal targa.

Fits:
Porsche 911 1974-85

Diagram Ref no.46

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

91156509145

The product you are viewing cross references to these numbers

Rear roll bar seal targa.

Fits:
Porsche 911 1974-85

Diagram Ref no.46

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

91156509145

The product you are viewing cross references to these numbers

Reinforcement plate set Targa roof - 2 pieces
These plates are fitted to the Targa frame area to bolster structural rigidity, reduce frame flex, and help maintain proper alignment of the removable Targa roof section. Made from aluminium with OE-style dimensions and finish, the set offers reliable support for the roof structure and helps protect the body from stress cracks or deformation caused by chassis flex or road loads. 
Sold as a set of two plates - one each side of the Targa hoop area.

Fits:
Porsche 911 - 1967 to 1985
Porsche 912 - 1967 to 1969

• Material: Aluminium, offering strength while reducing added weight.
• Fitment: Left and right sides of the Targa roof frame

Over time, the Targa frame section can suffer fatigue, stress cracking, or deformation due to removable roof panels, body flex, or prolonged road use. These issues can lead to misalignment of the roof, subtle leaks, wind noise or diminished structural integrity. Installing a new reinforcement plate set restores correct support, helps maintain chassis integrity and protects the Targa roof fit and body alignment for years to come.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

90159800240

The product you are viewing cross references to these numbers

Reinforcement plate set Targa roof - 3 pieces 

Fits:
Porsche 911 - 1967 to 1989
Porsche 912 - 1967 to 1969
Porsche 964 - 1989 to 1994

Set of 3 reinforcement plates for the Targa roof.
Plates are made of aluminum  

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

90159800240

The product you are viewing cross references to these numbers

Rennline Targa top locking pin, Stainless steel.
Sold Individually (2 required per car).

Fits:
Porsche 911/912/930 1965-85

Rennline's Stainless Steel Targa top locking pin replaces the pot metal factory unit that is prone to splitting. Once split, your targa top latch will be inoperable, leaving you without a roof over your head. Replace yours with Rennline's precision machined, 304 stainless steel upgrade.

Repair Mount set.
Restore the front mounting integrity of your Porsche 911 Targa’s / Cabrio's roof mechanism with this repair mount. Specifically designed for 911 Targa (1967-1985) and Cabriolet models (1982-1985), this kit includes mount and tension spring to replace worn or damaged front roof attachment points.
2pcs will be required if you want to repair both mechanisms.

Fits:

• Porsche 911 1965-1968 2.0L / 912 SWB (F)
• Porsche 911 1968-1973 2.2L / 2.4L / 2.7L RS LWB (F)
• Porsche 911 1974-1977 2.7L / 1976-77 3.0 Carrera
• Porsche 911 1978-1983 3.0L / SC
• Porsche 911 1984-1986 3.2L
• Porsche 911 1975-1977 3.0L Turbo (930)
• Porsche 911 1978-1989 3.3L Turbo (930)

Fits On To Diagram Ref No 3

What This Product Does:

• The Targa roof or Convertible top mechanism on classic 911s uses mounts/attachments to latch, pivot or tension the roof panel correctly.
• This repair mount is likely a small but critical component: it could serve as a mount point or pivot for the front Targa roof bar, or the latch/hinge assembly.
• The included tension spring suggests it plays a role in the roof-mechanism’s spring-loaded or tensioned latch/pivot function.
• Because it is labeled “repair mount”, it is likely used when the original mount has worn, broken, or been replaced incorrectly.

Signs You Might Need It:

• The roof panel doesn’t line up correctly, has excessive play, or the front bar doesn’t seat flush with the body when the roof is closed.
  
• The roof mechanism (especially the front section) feels loose or worn, or you find the mount/pivot is broken, cracked or missing.
  
• The tension spring associated with the mount is missing, fatigued, weak or broken, causing the roof latch not to hold firmly.
  
• During a restoration or refurb, the original mount is corroded, has poor repair history, or rust has eaten the mounting point.
• The roof could be mis-aligned, rattles, leaks at the front edge, or the roof bar is not seating properly — indicating the mount that holds the bar might have failed.

Why Replacement Matters:

• Roof integrity & alignment: The roof’s fit and finish depend on correct mounts and tensioning. A worn mount can lead to misalignment, water ingress, wind noise and reduced value.
  
• Correct operation: The roof mechanism must pivot, latch and hold reliably. A compromised mount can affect the reliable opening/closing of the roof.
  
• Preserves structural & aesthetic value: On classic 911 models, original mechanism parts matter for authenticity, fitment and resale.
  
• Prevents further damage: A faulty mounting point can lead to stress on adjacent components (roof bar, hinge, seals) — replacing the mount helps prevent accelerated wear.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

91156503141

The product you are viewing cross references to these numbers

Silentbloc bearing with pin for Targa roof
OE Match silentblock bearing for Porsche 911 and 964 Targa models. This replacement mounting component helps provide controlled support and vibration isolation within the Targa assembly, reducing direct metal-to-metal contact and helping maintain correct positioning of the adjoining components. Suitable for replacing a worn, hardened, split or damaged original silentblock where part number 91156503742 or 91156503842 is specified.

Fits:
Porsche 911 1974 - 1989 TARGA
Porsche 964 1989 - 1994 TARGA

Diagram ref no 34

A silentblock is a vibration-isolating mounting component designed to provide a degree of cushioning between adjoining parts. It helps absorb movement and vibration while supporting the component in its intended position. On these classic Porsche Targa applications, the silentblock bearing forms part of the associated Targa mounting assembly shown under diagram reference 34.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

91156503

The product you are viewing cross references to these numbers

Silentblock bearing with pin for Targa roof
The Genuine Porsche Silentblock Bearing (Part Numbers: 91156503742 / 91156503842) is an original equipment Targa roof mounting component designed for classic Porsche 911 and 964 Targa models. Also known as a Targa roof locating pin or bonded rubber mounting, this component forms part of the rear Targa roof mounting assembly, helping locate and support the removable roof panel in its correct position. Featuring a rubber-bonded construction, the Silentblock bearing helps absorb vibration and minimise unwanted movement between the roof panel and its mounting points.

Fits:
Porsche 911 1974 - 1989 TARGA
Porsche 964 1989 - 1994 TARGA

Diagram ref no 34

Manufactured to Porsche's original specifications, it provides precise fitment and reliable support, making it an ideal replacement for worn or damaged original mountings during Targa roof repairs, maintenance or classic Porsche restoration.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

91156503

The product you are viewing cross references to these numbers

 Socket head bolt for Targa roof catch, M 6 X 15.

Fits:
Porsche 911 1969-81 TARGA
Porsche 911 1984-86 TARGA

Click 'Zoom in' for large parts diagram.
Diagram ref no 4

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

99950900602

The product you are viewing cross references to these numbers

Targa bar filler piece.

Fits:
Porsche 911 1974-89 Targa

Click 'Zoom in' for large parts diagram.
Diagram ref no 16

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

91156513200

The product you are viewing cross references to these numbers

Targa bar inner air vent cover. Set of 2 Left & Right Porsche 911

Fits:
Porsche 911 Targa

Click 'Zoom in' for large parts diagram.
Diagram ref no 15

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

91156515758

The product you are viewing cross references to these numbers

Targa bar inner padding cover

Fits:
Porsche 911 1984-89 Targa
Porsche 964 1989-93 Targa

Click 'Zoom in' for large parts diagram.
Diagram ref no 12

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

90156551140

The product you are viewing cross references to these numbers

Targa Bar Plastic Screw. 24mm, Four needed. Price is for each.

Fits:
Porsche 911/912 1965-69 Targa
Porsche 911 1970-89 Targa
Porsche 964 C2 / C4 1989-94 Targa

This product supersedes Porsche's old part numbers:
- 90180115340

Diagram ref no 6

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

99906403740

The product you are viewing cross references to these numbers

Targa B-pillar cross sover, outer, black powder coating, with side louvres
Made from Steel.

Fits:
Porsche 911 Targa 2.7L-3.3L 08/73-07/89

Click 'Zoom in' for large parts diagram.
Diagram ref no 3

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

91156504348

The product you are viewing cross references to these numbers