Control Arms Front

RSS TARMAC SERIES 2-PIECE COMPLETE LOWER CONTROL ARM KIT - Front Axle (Pair of 2).



RSS Tarmac Series Motorsport Lower Control Arms are specifically engineered for use on lowered vehicles that have reduced travel struts/dampers such as PASM or M030 option. Alternatively if the car is equipped with high quality aftermarket or motorsport coilover kits ie Bilstein PSS10, KW V3 or Ohlins etc.

The Lower Control Arms are NOT COMPATIBLE with "Base Model Suspension" (long travel struts/dampers) or "Base Model struts/dampers with lowering springs."
Caution: Do not install on vehicles with Base Model struts/dampers as it may result in an unsafe driving condition with possibility of suspension bind when struts/dampers are fully extended or in full drop.

Fits front axle Porsche 987, 997/991 C2, C4, Turbo, 981/982/718

Includes:
- Adjustable/Non-Hydraulic Replacement Thrust Arm Bushings,
- 1mm/2mm/3mm/7mm Shims,
- Spherical Monoball Ends.
** Note: 981 and 991 Models may require additional Front Litronic or Torque Vector Sensor Brackets.

The RSS Tarmac Series – Motorsports Control Arms are designed for the Porsche driver who demands the absolute maximum in precision handling, feedback and control from their chassis. This system has been specially engineered to provide unmatched performance, quality, strength and serviceability. RSS Tarmac Series Control Arms address the performance related shortcomings of the OEM rubber mounted suspension components which were designed to reduce road noise and vibration for everyday street use. The use of rubber injected moldings in mounting components such as the control arms, thrust arms, upper links and toe arms is a compromise in regards to maximum suspension performance. The soft rubber deflects under suspension load which in turn causes unwanted movement (deflection) between the suspension and chassis. Data also shows that temporary changes in spring rates can occur as well. These movements and changes result in unnecessary corrections and inputs from the driver.

FEATURES & BENEFITS
• Replaceable Sub-Assemblies: For the extreme, repetitive track day enthusiast or racer, our high strength steel alloy spherical bearings (with a friction reducing, longevity increasing Teflon liner) outer and inner arm sub-assemblies can be replaced
unlike the motorsports arms, in which case a new set of arms will need to be purchased if the
spherical bearings are worn out.
• Adjustable Suspension Geometry: Adjust dynamic camber values and roll center heights with our
unique zinc plated steel bushings.
• Solid Monoball Control Arm Ends: Offers better handling and a more responsive suspension over the
factory one-piece rubber injected control arm by eliminating bushing deflection (also uses the same
high strength steel alloy spherical bearing found in our control arm monoball kit).
• 6061 Aerospace Grade Billet Aluminum Construction: Allows for a more uniform molecular structure
at every point of the arm over the cast components providing a more durable and inherently
stronger part. Manufacturing from billet aluminum rather than casting results in fewer impurities in
the metal.
• Anodized Aluminum Surfaces and Zinc Plated Steel Parts: Allows for better corrosion resistance
against the elements.

AVAILABLE FOR MOST PORSCHE 996, 986, 981, 982, 987 & 997 MODELS INCLUDING TURBO, GT2, GT2RS, GT3 & GT3RS

RSS TARMAC SERIES Motorsports Suspension Kits have been winning championships and races in various forms of motorsport (Road Racing to Rally) around the world. RSS is the suspension of choice of professional race teams, tuners, track day junkies, and driving enthusiasts around the world.
- 2015 PIRELLI WORLD CHALLENGE TC CHAMPIONS
- 2014 FIA SPANISH RALLY TARMAC CHAMPIONS
- 2013 ROLEX GRAND-AM GX CHAMPIONS
RSS High Performance Tarmac Series Suspension Components are designed, engineered and manufactured on location here in the USA.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

361

The product you are viewing cross references to these numbers

Front toe steer / bump steer kit XLARGE.



SET OF 2
replacement for 99634713104, 99634713103, 99134713100,

Fits:
FOR ALL Porsche 981, 982, GT4, 991 INCLUDING TURBO & GT3/GT3RS.

Also would fit Porsche 986, 996, 997, 987 that are running extreme amounts of negative camber or that have widened the front track width.

The RSS Adjustable Front Toe/Bump Steer XL Kit is designed for Porsche models that have been lowered. This kit will help minimize the suspension geometry change in the front of the vehicle. Allows for bump steer adjustment. Improves handling, feedback and control.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

371

The product you are viewing cross references to these numbers

Inner Spherical Bearing (Mono-ball) End Kit: SET OF 2.



Fits
Porsche 991 GT3 OE Front Control Arms
Porsche 981 GT4 Front and Rear Control Arms
Porsche 986, 987, 996, 997 with GT3/RS OE Front or Rear Split Control Arms,

Fits any RSS Tarmac Series Lower Control Arm or replaces any OE Porsche Split Arm Inner Bushing.
Provides a Bolt On Mono-Ball Performance Solution replacing rubber mounted OE inner mono-balls. RSS Longer studs allow for more negative camber adjustment / gain vs. OE inner bushing. For camber shim kits see RSS Part # 308.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

3-256

The product you are viewing cross references to these numbers

Lower Control Arm Adjusting Shims for Porsche Models



Price: One Alignment Shim

RSS alignment shims are designed for use with factory or aftermarket 2-piece motorsport style control arms. Perfect for obtaining more negative camber and adjusting track width during setup.

Shims are available in a variety of sizes including 1mm, 2mm, 3mm, 5mm, 7mm, 10mm and 11mm.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

300

The product you are viewing cross references to these numbers

RSS Tarmac Series Lower Control Arm - Outer Ball Joint Pin Rebuild Kit. 1 Kit Per RSS Lower Control Arm (Fits: Part #s: 356, 357, 361, 372, 373, 374 and 366)



Includes:
1 x Tapered Stud,
1 x Upper Lock Nut,
1 x Lower Lock Nut and
4 x Roll Center Spacers/Washers.

1 Kit Per RSS Lower Control Arm (Fits: Part #s: 356, 357, 361, 372, 373, 374 and 366).

USER NOTE: A new 380 Kit should be installed once ball joint pin has been removed from hub. See Lower Control Arm Notes.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

380

The product you are viewing cross references to these numbers

Outer ball joint pin rebuild kit for Front bump RSS toe steer link/arm. Fits Part # 370 + 371



Kit includes: 1x Tapered Stud, 1 x Upper Lock Nut, 1 x Lower Lock Nut, 2 x Stud Spacers/Washers.

USER NOTE: A new 382 Kit should be installed once ball joint pin has been removed from hub.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

382

The product you are viewing cross references to these numbers

Outer ball joint pin rebuild kit for RSS Rear toe steer link/arm , Fits part #312 and #301



Kit includes: 1x Tapered Stud, 1 x Upper Lock Nut, 1 x Lower Lock Nut, 2 x Stud Spacers/Washers

USER NOTE: A new 381 Kit should be installed once ball joint pin has been removed from hub

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

381

The product you are viewing cross references to these numbers

Inner Spherical Bearing (Mono-ball) End Kit: SET OF 2.

Brand:

Fits
Porsche 991 GT3  (not RS) OE Front Control Arms,
Porsche 981 GT4 Front and Rear Control Arms,
Porsche 986, 987, 996, 997 with GT3/RS OE Front or Rear Split Control Arms,
Fits any RSS Tarmac Series Lower Control Arm or replaces any OE Porsche Split Arm Inner Bushing. Provides a Bolt On Mono-Ball Performance Solution replacing rubber mounted OE inner mono-balls.

The Extra Long Monoball Housing Design (+15mm) allows for more negative camber adjustment / gain vs. standard aftermarket or OE inner bushings. The XL Design allows for proper stud engagement between inner and outer control arm with when running aggressive negative camber settings. For camber shim kits see RSS Part # 308.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

3-307

The product you are viewing cross references to these numbers

Spherical bearing inner GT3 monoballs for factory GT3 lower arm.

1 kit required per axle



Fits
Porsche 986 Boxster - Front and Rear
Porsche 987 Boxster and Cayman - Front and Rear
Porsche 996 - Front and Rear
Porsche 997 - Front and Rear
Porsche 981 - Front and Rear
Porsche 718 - Front and Rear
Porsche 991 - Front Only
Porsche 992 - Front Only
* Not For '12+ 991, 992 GT3/GT4

GT3 Street Inner Spherical Bearing Module

Unlike the factory rubber bushed GT3 inner control arms, our spherical bearings do not deflect under load.
They are fully weather sealed to keep out water and grit for extended life.

• Use in combination with factory GT3 street type control arm only
• Does not fit 991 GT3 or GT4 arms
• Easy Bolt-On
• Weather-sealed
• Sold as pair
• Front and Rear for 996, 997, 986, 987, 981, 718
• Front only on 991

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

2180030

The product you are viewing cross references to these numbers

Track Control Arm and Bush Kit Adjustable uses our Black 95A material for both bushes for ultimate performance and is supplied with an offset outer sleeve and CNC machined inner sleeve with spanner to allow for on-car adjustment of both caster and camber, for quick and easy optimisation of your wheel alignment.

PACK OF 2

This arm features suspension geometry tuning, with a caster increase of up to 0.4° and camber adjustment of +/- 0.75°

OEM Part Number: 98133105301
OEM Part Number: 99733104180
OEM Part Number: 99634105318



We're excited to introduce our new range of complete replacement Track Control Arm and Bush Kits for a number of Porsche models including 911 996, 997, 991, and Boxster / Cayman 718, 981, 986, 987.

Fits:
FRONT Diagram reference 2F
Porsche 997 GT2, GT3 & GT3RS
Porsche 986 Boxster (1997-2004)
Porsche 996 (1997-2005)

REAR Diagram reference 5R
Porsche 997 GT2, GT3 & GT3RS
Porsche 997 inc. Turbo
Porsche 718 Boxster/Cayman
Porsche 981 Boxster/Cayman
Porsche 986 Boxster (1997-2004)
Porsche 987 Boxster (2005-2012)
Porsche 987C Cayman (2005 - 2012)
Porsche 996 (1997-2005)


CONTENTS (parts per pack):

2 x Short Adjustable Stainless Steel Sleeves
1 x C45 Spanner
2 x Stainless Steel Washers

Pre-assembled parts:
2 x Cast Aluminium Track Control Arms
2 x Outer Bushes
2 x Inner Bushes
2 x Long Adjustable Stainless Steel Sleeves
2 x Ball Joint Nuts

Partnering with Chassis Technology Europe (CTE), a specialist in the manufacture of suspension and steering parts, we can now supply a high-quality cast control arm pre-assembled with our signature polyurethane bushes for a 'fit and forget' product, designed specifically for high performance and convenience of use with the added peace of mind of our Lifetime Warranty *.

Simply remove the old arm and refit!

Both Adjustable and Non-Adjustable bush options are available to suit differing driving and performance requirements.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

PF57K-1001G

The product you are viewing cross references to these numbers

Track control arm and bush kit uses a Black 95A inner bush and Purple 80A outer bush, providing a direct replacement alternative to worn OEM parts.

PACK OF 2

OEM Part Number: 98133105301
OEM Part Number: 99733104180
OEM Part Number: 99634105318



We're excited to introduce our new range of complete replacement Track Control Arm and Bush Kits for a number of Porsche models including 911 996, 997, 991, and Boxster / Cayman 718, 981, 986, 987.

Fits:
FRONT Diagram reference 2F
Porsche 997 GT2, GT3 & GT3RS
Porsche 986 Boxster (1997-2004)
Porsche 996 (1997-2005)

REAR Diagram reference 5R
Porsche 997 ALL inc GT2, GT3 & GT3RS
Porsche 997 MK2 ALL inc. Turbo
Porsche 718 Boxster/Cayman
Porsche 981 Boxster/Cayman
Porsche 986 Boxster (1997-2004)
Porsche 987 Boxster (2005-2012)
Porsche 987C Cayman (2005 - 2012)
Porsche 996 (1997-2005)


CONTENTS (parts per pack):

2 x Cast Aluminium Track Control Arms
Pre-assembled parts:
2 x Outer Bushes
2 x Inner Bushes
2 x Short Stainless Steel Sleeves
2 x Long Stainless Steel Sleeves
2 x Ball Joint Nuts


Partnering with Chassis Technology Europe (CTE), a specialist in the manufacture of suspension and steering parts, we can now supply a high-quality cast control arm pre-assembled with our signature polyurethane bushes for a 'fit and forget' product, designed specifically for high performance and convenience of use with the added peace of mind of our Lifetime Warranty *.

Simply remove the old arm and refit!

Both Adjustable and Non-Adjustable bush options are available to suit differing driving and performance requirements.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

PF57K-1001

The product you are viewing cross references to these numbers

Track control arm and bush kit Black series

PACK OF 2

OEM Part Number: 98133105301
OEM Part Number: 99733104180
OEM Part Number: 99634105318



We're excited to introduce our new range of complete replacement Track Control Arm and Bush Kits for a number of Porsche models including 911 996, 997, 991, and Boxster / Cayman 718, 981, 986, 987.

Fits:
FRONT Diagram reference 2F
Porsche 997 GT2, GT3 & GT3RS
Porsche 986 Boxster (1997-2004)
Porsche 996 (1997-2005)

REAR Diagram reference 5R
Porsche 997 GT2, GT3 & GT3RS
Porsche 997 inc. Turbo
Porsche 718 Boxster/Cayman
Porsche 981 Boxster/Cayman
Porsche 986 Boxster (1997-2004)
Porsche 987 Boxster (2005-2012)
Porsche 987C Cayman (2005 - 2012)
Porsche 996 (1997-2005)


CONTENTS (parts per pack):

2 x Cast Aluminium Track Control Arms
Pre-assembled parts:
2 x Outer Bushes
2 x Inner Bushes
2 x Short Stainless Steel Sleeves
2 x Long Stainless Steel Sleeves
2 x Ball Joint Nuts

Partnering with Chassis Technology Europe (CTE), a specialist in the manufacture of suspension and steering parts, we can now supply a high-quality cast control arm pre-assembled with our signature polyurethane bushes for a 'fit and forget' product, designed specifically for high performance and convenience of use with the added peace of mind of our Lifetime Warranty *.

Simply remove the old arm and refit!

Both Adjustable and Non-Adjustable bush options are available to suit differing driving and performance requirements.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

PF57K-1001BLK

The product you are viewing cross references to these numbers